收藏 分享(赏)

ASTM_F_502_-_08_2019.pdf

上传人:益****师 文档编号:189494 上传时间:2023-03-04 格式:PDF 页数:3 大小:84.82KB
下载 相关 举报
ASTM_F_502_-_08_2019.pdf_第1页
第1页 / 共3页
ASTM_F_502_-_08_2019.pdf_第2页
第2页 / 共3页
ASTM_F_502_-_08_2019.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F50208(Reapproved 2019)Standard Test Method forEffects of Cleaning and Chemical Maintenance Materials onPainted Aircraft Surfaces1This standard is issued under the fixed designation F502;the number immediately following the designation indicates the year of originaladoption or,in the cas

2、e of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test meth

3、od covers determination of the effects ofcleaning solutions and liquid cleaner concentrates on paintedaircraft surfaces(Note 1).Streaking,discoloration,and blister-ing may be determined visually.Softening is determined witha series of specially prepared pencils wherein determination ofthe softest pe

4、ncil to rupture the paint film is made.NOTE1This test method is applicable to any paint film that is exposedto cleaning materials.MIL-PRF-85285 has been selected as a basicexample.When other paint finishes are used,refer to the applicablematerial specification for panel preparation and system curing

5、 prior totesting.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concer

6、ns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with interna

7、tionally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D329 Specif

8、ication for AcetoneD1193 Specification for Reagent Water2.2 Military Standards:3MIL-PRF-85285 Coating:Polyurethane,Aircraft and Sup-port EquipmentA-A-58054 Abrasive Mats,Non-Woven Non-MetallicMIL-PRF-23377 Primer Coatings:Epoxy,High SolidsMIL-DTL-81706 Chemical Conversion Materials for Coat-ing Alum

9、inum and Aluminum Alloys2.3 Federal Standards:3FED-STD-595 Colors Used in Government Procurement2.4 Industry Standards:4SAE-AMS-QQ-A-250/13 Aluminum Alloy Alclad 7075,Plate and Sheet3.Materials3.1 Drawing Pencils(Note 2)6B,5B,4B,3B,2B,B,HB,F,H,2H,4H,5H,and 6H.3.2 Fine Sand Paper,180 to 320 grit.3.3

10、Abrasive Mats,A-A-58054,aluminum oxide,fine orvery fine.3.4 Acetone,in accordance with Specification D329.3.5 MIL-PRF-85285 Coating,polyurethane,Aircraft andSupport Equipment,FED-STD-595 Color No.17875,insigniawhite.3.6 MIL-PRF-23377 Primer Coating,epoxy polyamide,chemical-and solvent-resistant.3.7

11、Chemical Conversion Materials,MIL-DTL-81706,Class 1A,for coating aluminum and aluminum alloys.3.8 Distilled or Deionized Water,in accordance with Speci-fication D1193,Type IV.NOTE2All pencils in a set must be from one manufacturer(forexample,Venus,Eagle,and so forth).1This test method is under the j

12、urisdiction of ASTM Committee F07 onAerospace and Aircraft and is the direct responsibility of Subcommittee F07.07 onQualification Testing of Aircraft Cleaning Materials.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 1977.Last previous edition approved in 2013 as F502

13、08(2013).DOI:10.1520/F0502-08R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Department of Def

14、ense Single Stock Point(DODSSP)WebServer at http:/dodssp.daps.dla.mil using ASSIST Quick Search.4Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United Stat

15、esThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trad

16、e(TBT)Committee.1 4.Safety Precautions4.1 All safety regulations prescribed for spray application ofpolyurethane paints shall be strictly adhered to in the use of thistest method.4.2 The testing procedure shall be conducted in a well-ventilated area.5.Test Specimens5.1 SAE-AMS-QQ-A-250/13 Aluminum Alloy Alclad7075-T6,Plate and Sheet.6.Test Solutions6.1 Concentrated(as received,if a liquid).6.2 In use dilution,if diluent is water,see 3.8.7.Procedure7.1 Preparation of PencilsPrepare a set of drawi

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2