收藏 分享(赏)

ASTM_F_2336_-_17.pdf

上传人:益****师 文档编号:189721 上传时间:2023-03-04 格式:PDF 页数:5 大小:84.49KB
下载 相关 举报
ASTM_F_2336_-_17.pdf_第1页
第1页 / 共5页
ASTM_F_2336_-_17.pdf_第2页
第2页 / 共5页
ASTM_F_2336_-_17.pdf_第3页
第3页 / 共5页
ASTM_F_2336_-_17.pdf_第4页
第4页 / 共5页
ASTM_F_2336_-_17.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F233617An American National StandardStandard Guide forRoller Hockey Playing Facilities1This standard is issued under the fixed designation F2336;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A

2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe purpose of this guide is to reach common understanding by providing a guide for the designand construction of roller hockey playing fa

3、cilities.Attention is called to the alternative dimensionsof the playing surface depending upon the type of use and the age of the user.In the interest of future standardization,it is recommended that surface dimensions of all newfacilities be classified in accordance with those found in this guide.

4、It is recognized that roller hockey playing facilities also are used for figure skating,speed skating,and pleasure skating.Organizers of these sports may adopt the present standard as written,or modifythe guide in accordance with their special interests.1.Scope1.1 This guide covers the provisions fo

5、r consistent safetyconsiderations in the design and construction of new rollerhockey rinks in order to reduce potential safety hazards.It isintended to standardize game conditions and establish guide-lines that will provide a level of conformity for the purpose ofcompetition and reduce potential haz

6、ards to players and gameofficials.1.2 This guide should be taken into consideration byarchitects,designers,engineers,construction contractors,andappropriate inspectors who may be involved in the design andconstruction of new roller hockey rinks.This guide applies tothe development of new arenas and

7、to existing facilities thatwill be renovated.1.3 This guide takes into consideration that most ice hockeyrinks with concrete surfaces can be acceptable for rollerhockey.However,dasher boards must meet criteria respectiveof the specific activity.Facilities designed and constructed forroller hockey ma

8、y not be acceptable for ice hockey use.1.4 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of

9、 the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Deci

10、sion on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ANSI Standard:2ANSI Z535.2 Product Safety Signs and Labels3.Terminology3.1 Definitions of Terms Speci

11、fic to This Standard:3.1.1 blue line(optional),nblue line,1 ft(30.5 cm)inwidth,drawn parallel to and 60 ft(18.3 m)from the goal lineand extending up to the top of the boards.3.1.2 board cap or railing,nwood,plastic,or plastic-coated wood material 3 6 1 in.(7.62 6 2.54 cm)in width,attached at right a

12、ngles to the top of the boards3.1.3 center circle,nblue circle,2 in.(5.1 cm)in width,30ft(9.1 m)in diameter,whose center point is the midpoint of thecenter line.3.1.4 center face-off spot,ncircular blue spot,1 ft(30.5cm)in diameter,whose center point is the midpoint of thecenter line circle.1This gu

13、ide is under the jurisdiction of ASTM Committee F08 on SportsEquipment,Playing Surfaces,and Facilities and is the direct responsibility ofSubcommittee F08.66 on Sports Facilities.Current edition approved May 15,2017.Published May 2017.Last previousedition approved in 2005 as F2336 05 which was withd

14、rawn in January 2014 andreinstated in May 2017.DOI:10.1520/F2336-17.2Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international sta

15、ndard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.5

16、center line,nred line,1 ft(30.5 cm)in width,thatdivides the surface into two halves,drawn at right angles to thelong axis of the playing surface and extending up to the top ofthe boards.3.1.6 dasher boards,nwall of wood or plastic-coatedwood,fiberglass,or other high-impact material that enclosesand is part of the playing surface;also called the boards.3.1.7 enclosure,npart of the playing facility that sur-rounds the perimeter of the surface and consists of a lowersection(the kick-plate)that cont

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2