1、Designation:F193501(Reapproved 2018)An American National StandardStandard Test Method forMeasuring the Headroom of a Backpacking orMountaineering Tent1This standard is issued under the fixed designation F1935;the number immediately following the designation indicates the year oforiginal adoption or,
2、in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers tents for use in the sports ofbackpacking and mountaineering.It
3、 establishes requirementsfor the testing and marking of tents.1.2 This test method may contain test methods that do notentirely simulate real life situations.This test method isdesigned to give reproducible results in a laboratory andthereby a means for product comparison.1.3 This standard does not
4、purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard
5、 was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Terminolo
6、gy2.1 Definitions of Terms Specific to This Standard:2.1.1 tenta portable shelter made primarily of fabricweighing less than 3 oz/yd2,designed to be carried by theoccupants for while backpacking or mountaineering.2.1.2 usable headroomthe interior vertical measurementof a tent measured from the tent
7、floor to the high point on theceiling using a simple fixture that simulates an average usershead.3.Summary of Test Method3.1 The tent should be pitched on a flat surface in accor-dance with the companys supplied pitching instructions.3.2 The fixture shall be placed inside the tent.The ball israised
8、until it comes into contact with the ceiling,wall,poles,or any other obstructions inside the tent.3.3 The tape measure will now be hanging directly belowthe ball.The headroom measurement will be where themeasuring tape hits the tent floor.If the tent does not have afloor,record the measurement to th
9、e surface the tent has beenset up on.4.Significance and Use4.1 This test method can be used to quantify and compareheadroom of backpacking and mountaineering tents.Themeasured headroom can be used as a manufacturing standardor a measurement that can be used by consumers to comparethe interior height
10、 of a variety of tents,or both.5.Apparatus5.1 Specifications for Headroom Measurement Fixture(seeFig.1):5.1.1 Styrofoam ball 6 inches in diameter(mean width ofmale head=6.1 in.).25.1.2 Tape Measure,14in.GraduationsThe tape ismounted into the bottom of the Styrofoam ball,and the first 6inches are rem
11、oved from the tape.In this way,the reading willbe simple and accurate.6.Conditioning6.1 Tests may be completed under ambient conditions.Incases of dispute,test samples shall be conditioned in accor-dance with 6.2.6.2 The tent samples are first erected and dried in anatmosphere with a relative humidi
12、ty of less than 10%for aminimum period of 24 h.They are then placed in an atmo-sphere of 50 6 5%relative humidity,20 6 2 C for aminimum period of 72 h.Tests may then be done outside theconditioning room,but the temperature shall be 23 6 5 C andthe tests shall begin within 5 min.of removal from condi
13、tion-ing and be completed within 4 h.1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment,Playing Surfaces,and Facilities and is the direct responsibility ofSubcommittee F08.22 on Camping Softgoods.Current edition approved Oct.1,2018.Published November 2018.Originally
14、approved in 1998.Last previous edition approved in 2011 as F1935 01(2011).DOI:10.1520/F1935-01R18.2Henry Dreyfuss Associates,The Measure of Man and Woman:Human Factorsin Design,Whitney Library of Design,1993.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-29
15、59.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Ba
16、rriers to Trade(TBT)Committee.1 7.Sampling,Test Specimens,and Test Units7.1 The tent test specimen shall be new and in unusedcondition.When possible,it shall be selected randomly from aproduction lot of a given model of tent.It shall conform in allrespects to the manufacturers specifications for that model.8.Report8.1 The test report shall include the name of the tentmanufacturer,the model of tent tested,the date and location ofthe tests,the name(s)of personnel conducting the tests,if thetent is
