1、Designation:F171801(Reapproved 2013)An American National StandardStandard Specification forRotary Positive Displacement Distillate Fuel Pumps1This standard is issued under the fixed designation F1718;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the requirements applicable tothe design and construction of rotary po
3、sitive displacementdistillate fuel pumps for shipboard use.1.2 Lineal dimensions and units of force in this specificationare expressed as inches and pounds respectively.A companionmetric standard is in the process of preparation.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Ca
4、rbon Structural SteelA53/A53M Specification for Pipe,Steel,Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA106/A106M Specification for Seamless Carbon Steel Pipefor High-Temperature ServiceA193/A193M Specification for Alloy-Steel and StainlessSteel Bolting for High Temperature or High PressureS
5、ervice and Other Special Purpose ApplicationsA194/A194M Specification for Carbon andAlloy Steel Nutsfor Bolts for High Pressure or High Temperature Service,or BothA240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and Strip for PressureVessels and for General Appli
6、cationsA269 Specification for Seamless and Welded AusteniticStainless Steel Tubing for General ServiceA276 Specification for Stainless Steel Bars and ShapesA312/A312M Specification for Seamless,Welded,andHeavily Cold Worked Austenitic Stainless Steel PipesA354 Specification for Quenched and Tempered
7、 Alloy SteelBolts,Studs,and Other Externally Threaded FastenersA434 Specification for Steel Bars,Alloy,Hot-Wrought orCold-Finished,Quenched and TemperedA449 Specification for Hex Cap Screws,Bolts and Studs,Steel,Heat Treated,120/105/90 ksi Minimum TensileStrength,General UseA563 Specification for Ca
8、rbon and Alloy Steel NutsA564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and ShapesA574 Specification forAlloy Steel Socket-Head Cap ScrewsA582/A582M Specification for Free-Machining StainlessSteel BarsA743/A743M Specification for Castings,Iron-Chromium,I
9、ron-Chromium-Nickel,Corrosion Resistant,for GeneralApplicationA747/A747M Specification for Steel Castings,Stainless,Precipitation HardeningB148 Specification for Aluminum-Bronze Sand CastingsB150/B150M Specification for Aluminum Bronze Rod,Bar,and ShapesB209 Specification for Aluminum and Aluminum-A
10、lloySheet and PlateB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,Rods,Wire,Profiles,and TubesB271 Specification for Copper-Base Alloy Centrifugal Cast-ingsB505/B505M Specification for Copper Alloy ContinuousCastingsB584 Specification for Copper Alloy Sand Castings forGeneral Appl
11、icationsD1418 PracticeforRubberandRubberLaticesNomenclatureD2000 Classification System for Rubber Products in Auto-motive ApplicationsD3951 Practice for Commercial PackagingF104 Classification System for Nonmetallic Gasket Materi-alsF467 Specification for Nonferrous Nuts for General UseF468 Specific
12、ation for Nonferrous Bolts,Hex Cap Screws,Socket Head Cap Screws,and Studs for General UseF593 Specification for Stainless Steel Bolts,Hex CapScrews,and StudsF594 Specification for Stainless Steel NutsF837 Specification for Stainless Steel Socket Head CapScrewsF880 Specification for Stainless Steel
13、Socket,Square Head,and Slotted Headless-Set Screws1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved May 1,2013.Published May 2013.Originally
14、approved in 1997.Last previous edition approved in 2006 as F1718 01(2006).DOI:10.1520/F1718-01R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document
15、Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 F912 Specification for Alloy Steel Socket Set ScrewsF1511 Specification for Mechanical Seals for ShipboardPump Applications2.2 ANSI Standard:3B16.24 Pipe Flan
16、ges and Flanged Fittings2.3 ANSI/HI Standard:33.6 Rotary Pump Tests2.4 AMS Standards:43215 Acrylonitrile Butadiene(NBR)Rubber Aromatic FuelResistant 65-754676 Bars and Forgings,Corrosion Resistant,Hot Finished,Precipitation Hardenable 66.5 Ni,3.0 AL,0.62 Ti,28 Cu4677 Bars and Forgings,Corrosion Resistant,Annealed 66.5Ni,2.9 AL,30 Cu5894 Bars,Sheet,and Plate,Alloy 60 Co,28 Cr,4.5 W,1.15C,Solution Heat Treated2.5 ABMA Standards:59 Load Ratings and Fatigue Life for Ball Bearings11 Load Ratings and
