1、Designation:F265807(Reapproved 2013)Standard Specification forType PSM Poly(Vinyl Chloride)(PVC)SDR 51 and SDR 64Sewer Pipe and Fittings1This standard is issued under the fixed designation F2658;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、 revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers requirements and test methodsfor materials,dimensions,workmanship,flattenin
3、g resistance,impact resistance,pipe stiffness,extrusion quality,joiningsystems and a form of marking for type PSM poly(vinylchloride)(PVC)SDR 51 and SDR 64 sewer pipe and fittings.1.2 Pipe and fittings produced to this specification should beinstalled in accordance with Practice D2321.1.3 The text o
4、f this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The values stated in inch-pound units are to be regardedas the standard.The
5、 values given in parentheses are forinformation only.1.5 The following precautionary caveat pertains only to thetest methods portion,Section 8,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the user
6、of this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784
7、Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow Applicati
8、onsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylCh
9、loride)(PVC)Plastic Piping SystemsD2749 Symbols for Dimensions of Plastic Pipe FittingsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsF412 Terminology Relating to Plastic
10、 Piping Systems2.2 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage33.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with Termi-nology D1600,unle
11、ss otherwise specified.The abbreviation ofpoly(vinyl chloride)plastics is PVC.3.1.1 The term PSM is not an abbreviation but rather anarbitrary designation for a product having certain dimensions.4.Significance and Use4.1 The requirements of this specification are intended toprovide pipe and fittings
12、 suitable for non-pressure drainage ofsewage and surface water.NOTE1Industrial waste disposal lines should be installed only withthe specific approval of the cognizant code authority since chemicals notcommonly found in drains and sewers and temperatures in excess of 60C(140F)may be encountered.NOTE
13、2See D2321 Standard Practice for Underground Installation ofThermoplastic Pipe for Sewers and Other Gravity-Flow Applications forinstallation recommendations.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee
14、F17.62 on Sewer.Current edition approved Feb.1,2013.Published February 2013.Previousedition approved in 2007 as F2658 07.DOI:10.1520/F2658-07R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volu
15、me information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohock
16、en,PA 19428-2959.United States1 5.Basic Materials5.1 Pipe shall be made of PVC plastic having a cellclassification of 12454 or 12364 as defined in SpecificationD1784.5.2 Fittings shall be made of PVC plastic having a cellclassification of 12454 or 13343 as defined in SpecificationD1784.5.3 Pipe and FittingCompounds that have different cellclassifications,because one or more properties are superior tothose of the specified compounds,are also acceptable.5.4 Rework MaterialThe manufacturer shall us
