1、Designation:F215501(Reapproved 2009)Standard Specification forPerformance of Hasps and Other Attachment Devices forPadlocks or Seals1This standard is issued under the fixed designation F2155;the number immediately following the designation indicates the year oforiginal adoption or,in the case of rev
2、ision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification d
3、escribes and grades various levels ofperformance to provide users of the standard with criteria uponwhich to select suitable hasps and other attachment devices.Noeffort has been made to include criteria for specially madehasps used by the Department of Defense or other highlysensitive applications.1
4、.2 The tests described are laboratory tests,and althoughthey simulate field conditions as to attacks,they do notduplicate these conditions.Tests described are repeatable in thelaboratory.1.3 Some users of this standard may wish to use hasps thathave special attributes not related to security.1.4 The
5、 values stated in SI units are to be regarded as thestandard.The inch-pound units given in parentheses areprovided for information only.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to estab
6、lish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2.Referenced Documents2.1 ASTM Standards:2F883 Performance Specification for Padlocks3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 attachment device,nan item
7、 consisting of any num-ber of members that act in combination with a padlock or sealto provide a locking security system.3.1.2 fixed hasp,na combination of elements that,whenaligned,provide holes though which a padlock shackle or sealmay pass to secure the elements.3.1.3 hasp,nan attachment device h
8、aving a hinged orfixed strap that engages a hasp staple to provide for theattachment of a padlock or seal.3.1.4 hasp staple,nan eye-or U-shaped element that isengaged by the slotted strap of a hasp and provides for theattachment of a padlock or seal.3.1.5 hasp staple pad,na component of a hasp stapl
9、e thatprovides a fastening medium for attachment of the hasp stapleto the mounting surface.3.1.6 hasp strap,na component of a hasp that engages ahasp staple.3.1.7 hasp strap pad,na component of a hasp strap thatprovides a fastening medium for attachment of the hasp to themounting surface.3.1.8 hinge
10、d hasp,na hasp that includes a hasp strap,ahasp strap pad,a hasp staple,and a hasp staple pad incombination such that the hasp strap,when closed,engages thehasp staple,providing for the attachment of a padlock or sealto cause the assembly to be latched and locked or sealed intoa secure system.3.1.9
11、latch,nan item consisting of any number of mem-bers that act in combination to fasten separate elements into aconnected whole,and provides for the unfastening of thiswhole.3.1.10 latching attachment device,nan attachment devicethat includes a latching feature that permits the assembly toremain engag
12、ed without the use of a padlock or seal.3.1.11 latching hasp,na hasp that includes a latchingfeature that permits the strap to remain engaged with the haspstaple without the use of a padlock or seal.3.1.12 rotating hasp staple,na hasp staple that is free toturn in its pad,generally to provide a latc
13、hing function byengaging the hasp strap,or to resist a torsional attack.4.General Requirements4.1 Tolerances:1This specification is under the jurisdiction of ASTM Committee F12 onSecurity Systems and Equipment and is the direct responsibility of SubcommitteeF12.50 on Locking Devices.Current edition
14、approved Nov.1,2009.Published March 2010.Originallyapproved in 2001.Last previous edition approved in 2001 as F2155 01.DOI:10.1520/F2155-01R09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume
15、 information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.1 Fixture TolerancesAll tolerances shall follow stan-dard machining practices unless otherwise specified.4.1.
16、2 Test Setup Tolerances:4.1.2.1 Force61%of working range.4.1.2.2 Height63 mm(0.12 in.).4.1.2.3 Torque4%of reading.4.1.2.4 Weight610 g(0.02 lb).4.2 TemperatureAll tests shall be conducted between16C and 27C(61F and 81F).4.3 Test ReportsAll test reports shall be dated.5.Test Specimens5.1 Select specimens at random from the manufacturersfinished stock of each size and model being certified by themanufacturer.5.2 Select four hasps for the forcing tests.6.Preparation of Apparatus6.1 Tensile Loading D
