1、Designation:F314618Standard Test Method forImpact Attenuation of Turf Playing Systems Designated forRugby1This standard is issued under the fixed designation F3146;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard establishes a test method to be used whentesting a synthetic turf fields impact attenuation property forassessing its
3、suitability for rugby.1.2 The surface being tested will be located indoors oroutdoors and typically includes the entire surface,both withinthe boundary lines of the playing area and outside of it.Wherenon-turf surfaces exist within these areas,they shall beexcluded from the scope of this standard,un
4、less they arecovered either permanently or temporarily with synthetic turf.1.3 It is acceptable to use this test method,whereappropriate,as a test method for laboratory based testing ofsynthetic turf surfaces.1.4 The definition of a minimum performance requirementfor this test method is outside of t
5、he scope of this standard.Where reference is made to a minimum requirement this isintended for demonstration and clarification purposes only.1.5 This test method establishes a method of reporting testresults.1.6 The values stated in SI units are to be regarded asstandard.Where values are given in pa
6、renthesis they aremathematical conversions to inch-pound units that are pro-vided for information purposes only and are not consideredstandard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard t
7、o establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Princi
8、ples for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2F355 Test Method for ImpactAttenuation of Playing SurfaceSystems,Other Protective Sport Systems,and
9、 MaterialsUsed for Athletics,Recreation and PlayF2650 Terminology Relating to Impact Testing of SportsSurfaces and Equipment2.2 World Rugby Documents:3Regulation 22 Standard Relating to the Use of Rugby TurfWorld Rugbys Artificial Turf Performance Specification3.Terminology3.1 Except as noted,defini
10、tions in this standard are inaccordance with terms defined in Terminology F2650.3.2 Definitions:3.2.1 synthetic turf system,na synthetic surface intendedfor use in sport consisting of varying elements including butnot limited to a stitched or woven carpet,stabilizing infill,performance infill and a
11、shock absorbing sub-material.3.2.2 critical fall height(CFH),na measure of the impactattenuation performance of a surface;defined as the highesttheoretical drop height from which a surface is estimated tomeet the impact attenuation performance criterion specified.3.2.3 critical time value,nt2 t1wher
12、e t1and t2are theinitial and final times(in seconds)of the interval during whichHIC attains maximum value.3.2.4 drop height test,nthe combined drop test(s)per-formed at one specific drop height(see Fig.1).3.2.5 drop test,nan individual drop of the E missile(asdefined in Test Method F355)at a test po
13、int,where the drop hasbeen performed and recorded in accordance with prescribedmethodology(see Fig.1).3.2.6 head injury criterion(HIC),nweighted impulsecriterion calculated from a head impact acceleration-timeprofile and used to quantify head impact severity.The HIC1This test method is under the jur
14、isdiction of ASTM Committee F08 on SportsEquipment,Playing Surfaces,and Facilities and is the direct responsibility ofSubcommittee F08.65 on Artificial Turf Surfaces and Systems.Current edition approved Aug.1,2018.Published November 2018.DOI:10.1520/F3146-18.2For referenced ASTM standards,visit the
15、ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from World Rugby,https:/www.worldrugby.org/.Copyright ASTM International,100 Barr Harbor Drive,P
16、O Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 calculation results in a severity index that is weighted by bothimpact acceleration magnitude and by the time for which highmagn
