1、Designation:F75814Standard Specification forSmooth-Wall Poly(Vinyl Chloride)(PVC)Plastic UnderdrainSystems for Highway,Airport,and Similar Drainage1This standard is issued under the fixed designation F758;the number immediately following the designation indicates the year of originaladoption or,in t
2、he case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This sp
3、ecification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride)(PVC)plastic pipe and couplings for use in subsurface drainagesystems of highways,airports,and similar applications innominal sizes of 4,6,and 8 in.and in pipe stiffnesses(PS)thatare designated as Ty
4、pe PS 28 and Type PS 46 in accordancewith its minimum pipe stiffness.1.2 Molded fittings for use with highway underdrain pipeare in accordance with Specification D3034.For convenience,some of these fittings are reproduced in Annex A1.1.3 The values stated in inch-pound units are to be regardedas the
5、 standard.The values given in parentheses are forinformation only.NOTE1Type PS 28 and Type PS 46 indicate“pipe stiffness”of 28 and46,respectively,as outlined in 11.1.NOTE2Pipe and fittings should be installed in accordance withPractice D2321,or applicable state or local specifications.1.4 The follow
6、ing safety hazards caveat pertains only to thetest methods portion,Section 11,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpracti
7、ces and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Ch
8、lorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molded Fittings byAcetone ImmersionD2321 Practice for Underground Installation of Thermop
9、las-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)
10、D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsD3212 Specification for Joints fo
11、r Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD4396 Specification for Rigid Poly(Vinyl Chloride)(PVC)and Chlorinated Poly(Vinyl Chloride)(CPVC)Com-pounds for Plastic Pipe and Fittings Used in NonpressureApplications(Withdrawn 2015)3F402 Practice for Safe Handling of Solvent Cements,
12、Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping Systems2.2 Federal Standard:Fed.Std.No.123 Marking for Shipments(Civil Agencies)42.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage41This specification is under the jurisdi
13、ction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.65 on LandDrainage.Current edition approved Nov.1,2014.Published December 2014.Originallyapproved in 1982.Last previous edition approved in 2007 as F758 95(2007)1.DOI:10.1520/F0758-14.2For refer
14、enced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.a
15、stm.org.4DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia,PA19111-5094 http:/quicksearch.dla.mil/.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Termino
16、logy3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.The abbreviation forpoly(vinyl chloride)plastic is PVC.4.Classification4.1 Two classes(or pipe stiffness)are included and desig-nated as PS 28 and PS 46 as determined in accordance with11.1.5.Materials5.1 The pipe shall be made of PVC plastic having aminimum cell classification of 12454 or 12364 as defined inSpecification D1784 or a minimu
