1、Designation:F81012Standard Specification forSmoothwall Polyethylene(PE)Pipe for Use in Drainage andWaste Disposal Absorption Fields1This standard is issued under the fixed designation F810;the number immediately following the designation indicates the year of originaladoption or,in the case of revis
2、ion,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers requirements and test methodsfor workmanship,flattening,dimensions,tolerances,stiff
3、ness,perforations,environmental stress cracking,bonding,and im-pact resistance for smoothwall perforated and nonperforatedpolyethylene(PE)pipe,including coextruded and closed pro-file pipe.Methods of marking are also included.1.2 This specification includes two stiffness classes,referredto as,“Stand
4、ard”and“Heavy Duty.”1.3 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.4 The text of this specification references notes andfootnotes that provide explanatory material.These notes andfootnotes,excluding those in table
5、s and figures,shall not beconsidered as requirements of this specification.1.5 The following precautionary caveat pertains only to thetest method portion,Section 7,of this specification:Thisstandard does not purport to address all of the safety problems,if any,associated with its use.It is the respo
6、nsibility of whoeveruses this standard to consult and establish appropriate safetyand health practices and determine the applicability of regu-latory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated
7、 Terms Relating to Plas-ticsD1693 Test Method for Environmental Stress-Cracking ofEthylene PlasticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Te
8、st Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2729 Specification for Poly(Vinyl Chloride)(PVC)SewerPipe and Fitt
9、ingsD2751 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Sewer Pipe and Fittings(Withdrawn 2014)3D2852 Specification for Styrene-Rubber(SR)Plastic DrainPipe and FittingsD3033 Specification for Type PSP Poly(Vinyl Chloride)(PVC)Sewer Pipe and Fittings(Withdrawn 1987)3D3034 Specification for Ty
10、pe PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsF412 Terminology Relating to Plastic Piping SystemsF481 Practice for Installation of Thermoplastic Pipe andCorrugated Pipe in Septic Tank Leach Fields2.2 Federal Standard:
11、Fed.Std.No.123 Marking for Shipments(Civil Agencies)42.3 Military Standard:4MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.The abbrevia
12、tion forpolyethylene is PE.4.Significance and Use4.1 The requirements of this specification are intended toprovide smoothwall pipe suitable for soil drainage and wastedisposal system absorption fields.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is
13、 the direct responsibility of Subcommittee F17.65 on LandDrainage.Current edition approved Nov.1,2012.Published January 2013.Originallyapproved in 1983.Last previous edition approved in 2007 as F810 07.DOI:10.1520/F0810-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact
14、ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Standardization Documents Order Desk,Bldg.4
15、 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 NOTE1Industrial waste disposal lines should be installed only withthe specific approval of the cognizant code authority since
16、 chemicals notcommonly found in drains and sewers and temperatures in excess of140F(60C)may be encountered.NOTE2The recommended uses of PE smoothwall pipe covered bythis specification do not require watertight pressure rated joints.ABS,PVC,or styrene fittings may be used provided they conform to Specifi-cations D2729,D2751,D3033,D3034,or D2852.5.Materials5.1 GeneralThose PE compounds used in the manufac-ture of PE smoothwall pipe shall conform with the require-ments of cell class 424410 as defin