1、Designation:F170018aStandard Specification forSolid Vinyl Floor Tile1This standard is issued under the fixed designation F1700;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicate
2、s the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers solid vinyl2floor tiles that aremonolithic,surface decorat
3、ed or printed,and protected by aclear wear layer.1.2 This type of floor covering is intended for use incommercial,light commercial,and residential buildings.Gen-eral information and performance characteristics which deter-mine serviceability and recommended use are included in thisspecification.1.3
4、This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 The
5、values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This international standard was developed in accor-dance with internationally recognized p
6、rinciples on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3F137 Test Method for Flexibility
7、 of Resilient Flooring Ma-terials with Cylindrical Mandrel ApparatusF141 Terminology Relating to Resilient Floor CoveringsF373 Test Method for Embossed Depth of Resilient FloorCoveringsF386 Test Method for Thickness of Resilient Flooring Ma-terials Having Flat SurfacesF410 Test Method for Wear Layer
8、 Thickness of ResilientFloor Coverings by Optical MeasurementF925 Test Method for Resistance to Chemicals of ResilientFlooringF1514 Test Method for Measuring Heat Stability of ResilientFlooring by Color ChangeF1515 Test Method for Measuring Light Stability of Resil-ient Flooring by Color ChangeF1914
9、 Test Methods for Short-Term Indentation and Re-sidual Indentation of Resilient Floor CoveringF2055 Test Method for Size and Squareness of ResilientFloor Tile by Dial Gage MethodF2199 Test Method for Determining Dimensional Stabilityof Resilient Floor Tile after Exposure to Heat2.2 Other Standards:A
10、NSI/ASQC Z1.41993 Sampling Procedures and Tablesfor Inspection by Attributes43.Classification3.1 The vinyl floor tiles covered by this specification shallbe classified as follows:3.1.1 Class IMonolithic Vinyl Tile.3.1.1.1 Type ASmooth Surface.3.1.1.2 Type BEmbossed Surface.3.1.2 Class IISurface-Deco
11、rated Vinyl Tile.3.1.2.1 Type ASmooth Surface.3.1.2.2 Type BEmbossed Surface.3.1.3 Class IIIPrinted Film Vinyl Tile.3.1.3.1 Type ASmooth Surface.3.1.3.2 Type BEmbossed Surface.3.2 The embossed surfaces may or may not be grouted withink.4.Ordering Information4.1 The purchaser shall state whether this
12、 specification is tobe used,select the preferred options permitted herein,andinclude the following contract requirements on the purchaseorder:1This specification is under the jurisdiction of ASTM Committee F06 onResilient Floor Coverings and is the direct responsibility of Subcommittee F06.80on Spec
13、ifications.Current edition approved March 1,2018.Published April 2018.Originallyapproved in 1996.Last previous edition approved in 2018 as F1700 18.DOI:10.1520/F1700-18A.2For solid vinyl definition,refer to Terminology F141.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact
14、 ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute,11 West 42nd St.,NewYork,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO
15、Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the
16、 World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.1.1 Title,number,and date of this specification,4.1.2 Class,type,and pattern number(Section 3),4.1.3 Quantity in square feet,pieces,or cartons,4.1.4 Size required(Section 6),4.1.5 Thickness required(Section 6),4.1.6 Lot formation if other than as specified in ANSI/ASQC Z1.41993(see Sections 8 and 10),4.1.7 Sampling if other than as specified in ANSI/ASQCZ1.41993(see Sections 8 and 10),4.1.8 Packing requirement if other than
