收藏 分享(赏)

ASTM_F_547_-_06_2012.pdf

上传人:益****师 文档编号:190387 上传时间:2023-03-04 格式:PDF 页数:16 大小:263.72KB
下载 相关 举报
ASTM_F_547_-_06_2012.pdf_第1页
第1页 / 共16页
ASTM_F_547_-_06_2012.pdf_第2页
第2页 / 共16页
ASTM_F_547_-_06_2012.pdf_第3页
第3页 / 共16页
ASTM_F_547_-_06_2012.pdf_第4页
第4页 / 共16页
ASTM_F_547_-_06_2012.pdf_第5页
第5页 / 共16页
ASTM_F_547_-_06_2012.pdf_第6页
第6页 / 共16页
亲,该文档总共16页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F54706(Reapproved 2012)Standard Terminology ofNails for Use with Wood and Wood-Base Materials1This standard is issued under the fixed designation F547;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revis

2、ion.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe terms included in these definitions are listed in alphabetical order under six headings tofacilitate quick reference.They are inte

3、nded to apply to metal nails.Some of these terms are alsoapplicable to plastic nails.Omitted are terms relating to tacks,pins,drift pins,dowels,studs,spikes,staples,and other fasteners,such as nail plates.Also omitted are terms relating to the testing and theperformance of nails,that is,their drivab

4、ility,withdrawal resistance,lateral load transmission,creep,protrusion resistance,and splitting;and methods of use,such as face,toe,side,and end-nailing,spacing,loading conditions,etc.These subject matters will be covered in a separate definition of termsrelating to mechanical fasteners.Common accep

5、tance and usage are the basis for most of the definitions listed.In some instances,this common usage results in more than one definition for a given term.In other cases,registeredtrademarks have become generic in nature;hence,they are included among the terms listed.Any such listing cannot be comple

6、te.As additional terms are referred to the Societys attention,theywill be included.An asterisk(*)behind the name of a nail indicates that this particular nail type is described inSpecification F1667.Whereas dimensions are normally not part of a definition,they are included in this standard becauseth

7、ey are essential in fully describing the fastener under consideration.The definitions are listed under the following headings:NailNail HeadsNail ThreadsNail TypesNail PointsMiscellaneous Terms1.Referenced Documents1.1 ASTM Standards:2A510 Specification for General Requirements for Wire Rodsand Coars

8、e Round Wire,Carbon SteelA700 Practices for Packaging,Marking,and Loading Meth-ods for Steel Products for Shipment(Withdrawn 2014)3F1667 Specification for Driven Fasteners:Nails,Spikes,andStaples2.TerminologyNAILnailstraight,slender fastener,usually pointed and headed;6in.or less in length;designed

9、to be driven;to hold two ormore pieces together or to act as support.(See screw nail;drive screw.)DISCUSSIONIn contrast to screwfastener,usually pointed andheaded;designed to be turned with a screwdriver or other device;having in its simplest form one or two continuous spiral threads(suchas a wood s

10、crew thread)or a helical thread(such as a machine screwthread)or combinations thereof(such as a sheet-metal screw thread).NAIL TYPESaluminum common nail*plain-shank,aluminum-alloy,1by 0.072 to 6 by 0.262-in.nails with flat532to1732-in.headand medium diamond point.apple-box nailcoated,regular-stock-s

11、teel,158and 134by0.080-in.nails with flat1564-in.head and medium diamondpoint.1This terminology is under the jurisdiction of ASTM Committee F16 onFastenersand is the direct responsibility of Subcommittee F16.05 on Driven andOther Fasteners.Current edition approved April 1,2012.Published May 2012.Ori

12、ginallyapproved in 1977.Last previous edition approved in 2006 as F547 06.DOI:10.1520/F0547-06R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document

13、Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 asbestosboard nailgalvanized,hardened-steel,helicallythreaded,114and 112by

14、 0.083-in.screwnails with flat,slightly countersunk,316-in.head and blunt diamond point.asbestos-shingle nail See shingle nail.asphalt-shingle nail See roofing nail.auto nailnail of14to 514-in.length,sheared off bright,smooth,knurled,or helically fluted,regular-stock-steel orstiff-stock,0.032-in.(21

15、-gage)to 0.162-in.(8-gage)wireand driven subsequently by the same machine at a rapid rate.This nail has a sheared-bevel or sheared-square point.barrel nail*bright or coated,regular-stock-steel,58by 0.067to 112by 0.092-in.nails with flat 0.148 to 0.219-in.head andmedium diamond point.basket nailbrigh

16、t,regular-stock-steel,58and34by 0.048-in.nails with large flat head and medium needle point.beer-case cleat nailbright,regular-stock-steel,1 by 0.080 to178by 0.106-in.nails with316to14-in.oval head andduckbill or clinch point.beer-case hinge,lock and latch nailbright,regular-stock-steel,58by 0.080 to 1516by 0.092-in.nails with oval316to732-in.head and duckbill or clinch point.beer-case strap nailbright,regular-stock-steel,114by 0.092to 2 by 0.113-in.nails with oval1564to-in.head and mediumdiamon

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2