1、Designation:F178819Standard Guide forIn-Situ Burning of Oil Spills on Water:Environmental andOperational Considerations1This standard is issued under the fixed designation F1788;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the yea
2、r of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers the use of in-situ burning to assist inthe control of oil spills on water.This guide is not applicab
3、le toin-situ burning of oil on land or the disposal of oil or oileddebris in incinerators.1.2 The purpose of this guide is to provide information thatwill enable spill responders to decide if burning will be used aspart of the oil spill cleanup response.Other standards addressthe use of ignition dev
4、ices(Guide F1990),the use of fire-resistant boom(Guide F2152),the use of burning in iceconditions(Guide F2230),the application of in-situ burning inships(Guide F2533),and the use of in-situ burning in marshes(Guide F2823).1.3 This is a general guide only.It is assumed that condi-tions at the spill s
5、ite have been assessed and that theseconditions are suitable for the burning of oil.It is also assumedthat permission to burn the oil has been obtained fromappropriate regulatory authorities.Variations in the behavior ofdifferent oil types are not dealt with and may change some ofthe parameters note
6、d in this guide.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4.1 ExceptionAlternate units are included in 7.5,7.7,and 7.8.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its
7、 use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principle
8、s on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2F1990 Guide for In-Situ Burning of Spill
9、ed Oil:IgnitionDevicesF2152 Guide for In-Situ Burning of Spilled Oil:Fire-Resistant BoomF2230 Guide for In-situ Burning of Oil Spills on Water:IceConditionsF2533 Guide for In-Situ Burning of Oil in Ships or OtherVesselsF2823 Guide for In-Situ Burning of Oil Spills in Marshes3.Terminology3.1 Definiti
10、ons:3.1.1 burn effciencyburn efficiency is the percentage ofthe oil removed from the water by the burning.3.1.1.1 DiscussionBurn efficiency is the amount(volume)of oil before burning;less the volume remaining as a residue,divided by the initial volume of the oil.3.1.2 burn ratethe rate at which oil
11、is burned in a givenarea.3.1.2.1 DiscussionTypically,the area is a pool and burnrate is the regression rate of the burning liquid,or may bedescribed as a volumetric rate.3.1.3 contact probabilitythe probability that oil will becontacted by the flame during burning.3.1.4 controlled burningburning whe
12、n the combustioncan be started and stopped by human intervention.3.1.5 fire-resistant boomsbooms intended for containmentof burning oil slicks(Guide F2152).3.1.6 in-situ burninguse of burning directly on the watersurface.1This guide is under the jurisdiction of ASTM Committee F20 on HazardousSubstan
13、ces and Oil Spill Responseand is the direct responsibility of SubcommitteeF20.15 on In-Situ Burning.Current edition approved July 1,2019.Published July 2019.Originally approvedin 1997.Last previous edition approved in 2014 as F1788 14.DOI:10.1520/F1788-19.2For referenced ASTM standards,visit the AST
14、M website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesTh
15、is international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TB
16、T)Committee.1 3.1.6.1 DiscussionIn-situ burning does not include incin-eration techniques,whereby oil or oiled debris are placed intoan incinerator.3.1.7 residuethe material,excluding airborne emissions,remaining after the oil stops burning.4.Significance and Use4.1 This guide is primarily intended to aid decision-makersand spill-responders in contingency planning,spill response,and training.4.2 This guide is not specific to either site or type of oil.5.Background5.1 Overview of Oil Burning:5.1.
