1、Designation:F263014Standard Guide forSelf-Closing/Self-Latching General-Purpose Gates1This standard is issued under the fixed designation F2630;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in par
2、entheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide establishes the recommended minimum re-quirements for the design,construction and performance ofself-closing and self-latching single leaf,ge
3、neral-purpose ac-cess gates.It is intended to provide an added degree ofreliability in the performance of the self-closing and self-latching devices mounted to these gates.1.2 This guide should be referenced whenever any otherstandard requires a single leaf access gate to be self-closing andself-lat
4、ching,with the exception of standards for pool oroutdoor child safety gates.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This s
5、tandard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.After installationand inspec
6、tion,it is the responsibility of the homeowner orproperty manager to inspect and adjust the hardware,or thegate,or both,to compensate for ground movement and otherfactors so that the gate continues to effectively self-close andself-latch.2.Terminology2.1 access gateany portion of a fence or barrier
7、that isdesigned to provide a pedestrian access way through the fenceor barrier.2.2 double leaf access gatewhere two independently op-erating gate leaves are situated directly next to each other.Alsoknown as double drive gates,the two leaves meet at one edgeforming a continuous barrier.Both leaves ar
8、e situated togetherbetween posts,walls,columns or combinations thereof.2.3 general-purpose access gatea gate designed for afence surrounding a home,garden,business,pets or otherproperty,marina or sports field,not including a swimming poolor child play area.2.4 pool or outdoor child safety gatea gate
9、 on a fence thatdeters a child or children from accessing a dangerous area,such as a street(traffic),equipment or a water feature.2.5 self-latching devicea latch that successfully engageson its own,without the application of manual pressure.2.6 single leaf access gatewhere one gate leaf is locatedbe
10、tween opposing stationary posts,columns,walls or combi-nation thereof.3.Significance and Use3.1 This guide sets forth minimum standard requirementsfor use in building codes and ordinances relating to self-closingand self-latching single leaf access,general-purpose gates.3.2 This guide does not apply
11、 to double leaf or double driveaccess gates.3.3 This guide does not have the effect of law,nor is itintended to supersede Americans with Disabilities Act(ADA)guidelines,local codes or ordinances of a more restrictivenature.4.General Performance4.1 Self-Closing General-Purpose Access GatesWhen itis s
12、pecified that single leaf access gates must be self-closing,they shall be fitted with a self-closing device(s)that will returnthe gate to the closed position and operate the latching devicewithout the application of manual force.4.2 Self-Latching General-Purpose Access GatesWhen itis specified that
13、single leaf access gates should be self-latching,they shall be fitted with a device that latches in the closedposition without the application of manual force.5.Requirements5.1 Self-Closing Single leaf access general-purpose gatesshall close from two open positions:12 in.from the gate to thelatch po
14、st and a 90 degree angle from the closed position of thegate without manual force.5.2 Self-Latching The latching device on single leafaccess general-purpose gates shall completely latch without1This guide is under the jurisdiction of ASTM Committee F14 on Fences and isthe direct responsibility of Su
15、bcommittee F14.15 on Other Fence Systems andComponents.Current edition approved Oct.1,2014.Published October 2014.Originallyapproved in 2007.Last previous edition approved in 2007 as F263007.DOI:10.1520/F2630-14.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1942
16、8-2959.United States1 manual force,through the action of the self-closing device,from two open positions:a static position 90 degrees from theclosed position or when the gate has been opened at least 12 in.5.3 The self-latching mechanism or self-closing deviceshould be capable of adjustment to compensate for changes ingate alignment during and after installation.5.4 The self-latching device on a single leaf general-purposeaccess gate shall be capable of sustaining manual force,including shaking,
