1、Designation:F267308Standard Safety Specification forSpecial Tip-Resistant Movable Soccer Goals1This standard is issued under the fixed designation F2673;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers safety requirements aimed atproviding for safer use of soccer goals and reducing injuriesand fatalities.1.2 This spec
3、ification addresses the risk of accidental tipover or pull over of soccer goals.1.3 This specification applies only to movable goals whoseinside measurements are 612to 8 ft(2 to 2.4 m)high and 18 to24 ft(5.5 to 7.3 m)wide.1.4 This specification applies only to movable goals meet-ing all criteria in
4、Guide F1938 and Safety and PerformanceSpecification F2056 and,in addition,meets criteria for tipresistance before installation.1.5 This specification covers special tip-resistant goals thatare intended to complement standard goals meeting GuideF1938 and Safety and Performance Specification F2056.The
5、segoals are designed to provide some additional degree of safetyif,by accident,they are not tied down or tied down incorrectly.1.6 This specification simulates two boys up to twelve yearsof age swinging together from the X-bar.NOTE1Injury data supplied to the committee indicates that approxi-mately
6、75%(74%)of the fatalities(1979-2003)were three to twelveyears of age.1.7 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.8 This standard
7、 does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Stan
8、dards:2F1938 Guide for Safer Use of Movable Soccer GoalsF2056 Safety and Performance Specification for SoccerGoals3.Terminology3.1 DefinitionsSee Guide F1938 and Safety and Perfor-mance Specification F2056 for definitions.4.Safety Requirements4.1 Soccer goals shall be subjected to the test outline i
9、nSection 5 and shall neither tilt over nor refuse to return to itsoriginal vertical position.4.2 Tests shall be applied to soccer goals in their originalunrestrained(no tie-down)condition.4.3 Tests shall be repeated three times.4.4 Tests shall be applied only to movable goals.4.5 Soccer goals shall
10、then meet all testing criteria,instructions,and labeling listed in Safety and PerformanceSpecification F2056 including anchoring.5.Stability Test5.1 Goals shall be set upon a flat,outdoor(earth)surface.5.2 Two weights shall be placed 1.5 ft(0.46 m)on each sideof the center of the X-bar of the goal(F
11、ig.1).5.3 The weights shall be composed of bags of sand weigh-ing 110 6 2 lb(50 6 1 kg)each.NOTE2The weights(5.3)are selected to simulate two twelve-year-oldboys.(Physical characteristics of children as related to death and injury forconsumer product safety design and use,95th percentile,twelve-year
12、-oldmale,109 lb(49 kg).)5.4 The weighed bags shall be tied firmly to the X-bar with12-in.(1.3-cm)ropes.5.5 Weights shall dangle from the rope and each bag spaced(vertically downward)so that the center of the bag is 12 6 1in.(30.5 6 2.5 cm)from the X-bar.1This specification is under the jurisdiction
13、of ASTM Committee F15 onConsumer Products and is the direct responsibility of Subcommittee F15.43 onSoccer Goal Safety.Current edition approved Feb.1,2008.Published February 2008.DOI:10.1520/F2673-08.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service a
14、t serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.6 Weights shall be simultaneously displaced at a 30 an
15、glefrom the vertical position(perpendicular to the cross-bar)withrope extended,held for 10 6 2 s,released,and allowed toswing freely(Fig.2).5.7 The test shall be repeated with the weights swung froma 30 angle on the opposite side.6.Labels6.1 No product covered by this specification and producedafter
16、 the approval date shall,by label,marking,or other means,indicate compliance unless it conforms to all requirementsherein.6.2 Soccer goals meeting this specification shall be labeled“Special Tilt-Resistant Goal Meeting ASTM F2673.”7.Keywords7.1 soccer goal;tilt-resistant goalFIG.1 Two Weights Applied at the Center of the X-Bar of the Goal and Spaced 3 ft(0.9 m)ApartFIG.2 Weights Simultaneously Displaced at a 30 Angle from the Vertical Position,Held for 10 6 2 s,Released,and Allowed to SwingFreel
