1、Designation:F312819An American National StandardStandard Specification forPoly(Vinyl Chloride)(PVC)Schedule 40 Drain,Waste,andVent Pipe with a Cellular Core1This standard is issued under the fixed designation F3128;the number immediately following the designation indicates the year oforiginal adopti
2、on or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers coextruded poly(vinyl chlo-ride)(PVC)plastic drain,was
3、te and vent pipe made toSchedule 40 iron pipe sizes(IPS)and produced by thecoextrusion process with concentric inner and outer solid PVClayers and the core consisting of closed-cell cellular PVC.Plastic which does not meet the material requirements specifiedin Section 5 is excluded from single layer
4、 and all coextrudedlayers.1.2 Fittings meeting the requirements of SpecificationD2665 and D3311 are suitable for use with pipe meeting therequirements of this specification.1.3 Poly(vinyl chloride)plastic which does not meet thedefinitions of virgin PVC plastic as given in 5.1 is excluded,asperforma
5、nce of plastic other than those defined as virgin wasnot determined.PVC rework plastic which meets the require-ments of rework plastic as given in 5.2 is acceptable.1.4 Reprocessed plastic or recycled plastic as defined inTerminology D883 is excluded.1.5 Recommendations for storage,joining and insta
6、llationare provided in Appendix X1,Appendix X2,and Appendix X3respectively.1.6 The text of this specification references notes,footnotesand appendices which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the speci
7、fication.1.7 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.8 This standard does not purport to address all of thesafety concerns,if an
8、y,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accor-dance with internationally
9、 recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for C
10、onditioning Plastics for TestingD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molde
11、d Fittings byAcetone ImmersionD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Im
12、pact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2665 Specification for Poly(Vinyl Chloride)(PVC)PlasticDrain,Waste,and Vent Pipe and FittingsD2855 Practice for the Two-Step(
13、Primer and Solvent Ce-ment)Method of Joining Poly(Vinyl Chloride)(PVC)orChlorinated Poly(Vinyl Chloride)(CPVC)Pipe andPiping Components with Tapered SocketsD3311 Specification for Drain,Waste,and Vent(DWV)1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems an
14、d is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved March 1,2019.Published March 2019.Originallyapproved in 2015.Last previous edition approved in 2015 as F312815.DOI:10.1520/F3128192For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Cu
15、stomer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1
16、9428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 Plastic Fittings PatternsD4396 Specification for Rigid Poly(Vinyl Chloride)(PVC)and Chlorinated Poly(Vinyl Chloride)(CPVC)Com-pounds for Plastic Pipe and Fitting
