1、Designation:F467M06a(Reapproved 2012)Standard Specification forNonferrous Nuts for General Use(Metric)1This standard is issued under the fixed designation F467M;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope*1.1 This specification covers the requirements for commer
3、-cial wrought nonferrous nuts in nominal thread diameters M6to M36 inclusive in a number of alloys in common use andintended for general service applications.1.2 Applicable bolts,cap screws,and studs for use with nutscovered by this specification are covered by SpecificationF468M.1.3 The values stat
4、ed in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.NOTE1This specification is the metric companion of SpecificationF467.2.Referenced Documents2.1 ASTM Standards:2B154 Test Method for Mercurous Nitrate Test for CopperAlloysB574 Specification for Lo
5、w-Carbon Nickel-Chromium-Molybdenum,Low-CarbonNickel-Molybdenum-Chromium,Low-CarbonNickel-Molybdenum-Chromium-Tantalum,Low-Carbon Nickel-Chromium-Molybdenum-Copper,andLow-CarbonNickel-Chromium-Molybdenum-Tungsten Alloy RodD3951 Practice for Commercial PackagingE18 Test Methods for Rockwell Hardness
6、of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys(Withdrawn 1989)3E53 Te
7、st Method for Determination of Copper in UnalloyedCopper by GravimetryE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)3E55 Practice for Sampling Wrought Nonferrous Metals andAlloys for Determination of Chemical CompositionE62 Test Methods for Chemical Analysis of
8、Copper andCopperAlloys(Photometric Methods)(Withdrawn 2010)3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc Alloys(Withdrawn 2010)3E76 Test Methods for Chemical Analysis of Nickel-CopperAlloys(Withdrawn 2003)3E92 Test Method for Vickers Hardness of Metallic Materials(Wi
9、thdrawn 2010)3E101 Test Method for SpectrographicAnalysis ofAluminumand Aluminum Alloys by the Point-to-Plane Technique(Withdrawn 1996)3E120 Test Methods for Chemical Analysis of Titanium andTitanium Alloys(Withdrawn 2003)3E165 Practice for Liquid Penetrant Examination for GeneralIndustryE227 Test M
10、ethod for Optical Emission SpectrometricAnalysis of Aluminum and Aluminum Alloys by thePoint-to-Plane Technique(Withdrawn 2002)3E354 Test Methods for Chemical Analysis of High-Temperature,Electrical,Magnetic,and Other Similar Iron,Nickel,and Cobalt AlloysE478 Test Methods for Chemical Analysis of Co
11、pper AlloysE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by the Inert GasFusion TechniqueF468M Specification for Nonferrous Bolts,Hex Cap Screws,and Studs for General Use(Metric)F606M Test Methods for Determining the Mechanical Prop-erties of Externally
12、and Internally Threaded Fasteners,Washers,and Rivets(Metric)F1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection1This specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.04 on N
13、onferrousFasteners.Current edition approved April 1,2012.Published May 2012.Originallyapproved in 1979.Last previous edition approved in 2006 as F467M 06a2.DOI:10.1520/F0467M-06R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.F
14、or Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Bar
15、r Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.2 ASME Standards:4B 1.13M Metric Screw ThreadsB 18.2.4.1M Metric Hex Nuts,Style 13.Ordering Information3.1 Orders for nuts under this specification shall include thefollowing information:3.1.1 Quantity(numbers of pieces of e
16、ach item and size);3.1.2 Name of item;3.1.3 Nominal thread diameter and thread pitch;3.1.4 Alloy number(Table 1);3.1.5 Stress relieving,if required(4.2.3);3.1.6“Shipment lot”testing,as required(Section 9);3.1.7 Source inspection,if required(Section 14);3.1.8 Certificate of compliance or test report,if required(Section 16);3.1.9 Additional requirements,if any,to be specified on thepurchase order(4.2.1,7.2,8.2,11.1,and 12.1),3.1.10 Supplementary requirements,if any;and3.1.11 ASTM specification and
