1、This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(
2、TBT)Committee.Designation:F2413-17NTERNATIONALStandard Specification forPerformance Requirements for Protective(Safety)Toe CapFootwearThis standard is issued under the fixed designation F2413:the number immediately following the designation indicates the year oforiginal adoption or,in the case of re
3、vision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.INTRODUCTIONFor more than six
4、ty years,the predecessor to this specification,ANSI Z41,established theperformance criteria for a wide range of footwear to protect from hazards that affect the personalsafety of workers.The value of these standards was recognized early in the history of Occupational Safety and HealthAdministration(
5、OSHA)and incorporated as a reference standard in the Code of Federal Regulations(29 CFR Part 1910.132 and 29 CFR Part 1910.136).The principal purpose of this standard is the certification of protective footwear.Certification mustbe performed by independent third party laboratories in order for footw
6、ear to bear the ASTM marking.The specification contains performance requirements for footwear to protect workersfeet from thefollowing hazards by providing:(1)impact resistance(I)for the toe area of footwear;(2)compressionresistance(C)for the toe area of the footwear;(3)metatarsal impact protection(
7、Mt)that reduces thechance of injury to the metatarsal bones at the top of the foot;(4)conductive properties(Cd)whichreduce hazards that may result from static electricity buildup;and reduce the possibility of ignition ofexplosives and volatile chemicals;(5)electric hazard protection(EH),to protect t
8、he wearer whenaccidental contact is by stepping on live electric wires;(6)static dissipative properties(SD)to reducehazards due to excessively low footwear electrical resistance that may exist where SD footwear isrequired;and(7)puncture resistance(PR)footwear devices.1.Scope1.4 Any changes to the or
9、iginal components of safety toe1.1 This specification covers minimum requirements for thefootwear such as replacing or adding after market footbeds/performance of footwear to provide protection against a varietyinserts could cause failure to any or all parts of this standardof workplace hazards that
10、 can potentially result in injury.rendering the ASTM marking invalid.1.2 This specification is not intended to serve as a detailed1.5 This specification is not applicable to overshoes withmanufacturing or purchasing specification,but can be refer-safety toe caps or strap on devices with safety toes.
11、enced in purchase contracts to ensure that minimum perfor-mance requirements are met.1.6 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for information1.3 Controlled laboratory tests used to determine compli-only.ance with the performance requirem
12、ents of this specificationshall not be deemed as establishing performance levels for all1.7 This standard does not purport to address all of thesituations to which individuals may be exposed.safery concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establ
13、ish appro-This specification is under the jurisdiction of ASTM Committee F13 onpriate safety,health,and environmental practices and deter-Pedestrian/Walkway Safety and Footwear and is the direct responsibility ofmine the applicability of regulatory limitations prior to use.Subcommittee F13.30 on Foo
14、twear.1.8 This international standard was developed in accor-Current edition approved Nov.1,2017.Published December 2017.Originallyapproved in 2005.Last previous edition approved in 2011 as F2413-11.DOl:dance with internationally recognized principles on standard-10.1520/F2413-17.ization established
15、 in the Decision on Principles for theCopyright ASTM Intemational,100 Barr Harbor Drive,PO Box C700.West Conshohocken.PA 19428-2959.United States1F2413-175.7.8.1 Puncture resistant devices shall show no signs ofFI/75/C/75de-lamination of layers or cracking after 1.5 million flexes.F75755.7.9 Punctur
16、e resistant devices shall show no sign ofFemaleImpactImpactCompressionCompressionResistantRatingResistantRatingcorrosion,de-lamination,or deterioration after being exposedFootwearFootwearto a 5 salt solution for 24 h,in accordance with Practice6.1.5 Lines 3 and 4 have been used to reference addition
17、alB117.sections in this standard.Section reference shall be in numeri-5.7.10 Any specimen that does not meet minimum puncturecal order.resistant requirements for the product constitutes a non-6.1.5.1(1)-Identifies protection against impact as discussedcompliance for the product category.in5.1.6.Labe
18、ling and Identification6.1.5.2(C)-Identifies protection against compression asdiscussed in 5.2.6.1 Labeling and identification of protective footwear with6.1.5.3(Mt)-Identifies footwear designed to be impactprotective toe cap is essential to ensure the wearer thatresistant to the top of the foot as
19、discussed in 5.3.footwear meets the required minimum performance of this6.1.5.4(Cd)-Identifies protection against conductive haz-specification(see Table 1).ards as discussed in 5.4.6.1.1 The label can be either a stitched in,stamped,or6.1.5.5(EH)-Identifies footwear constructed with andpressure sens
20、itized label or a combination of these methods.Amanufactured to have electrical insulation properties;electricalspecific four line format that identifies the type of footwear andhazard resistant as discussed in 5.5.the hazards for which it is designed to provide protection6.1.5.6(SD 100)-Identifies
21、footwear designed to reduceshould be used.The identification shall be enclosed in athe accumulation of excess static electricity as discussed inrectangular border and be placed on the inside or outside5.6.2.surface of either the tongue,gusset,shaft or quarter lining in6.1.5.7(SD 35)-Identifies footw
22、ear designed to reduce theone half pair.accumulation of excess static electricity as discussed in 5.6.2.3.6.1.2 Print size on labels shall be clearly visual to the eye6.1.5.8(SD/0)-Identifies footwear designed to reduce theand shall measure 3.175 mm(0.125 in.)or larger.For example:accumulation of ex
23、cess static electricity as discussed in 5.6.2.4.6.1.5.9(PR)-Identifies footwear designed to be punctureASTM F2413-11resistant as discussed in 5.7.MI/75C/756.1.6 Line 4 shall be used when more than 3 sections of thisMt/75 EHstandard apply to any one category.7.Marking and Compliance Requirements6.1.3
24、 Line/-Identifies that the footwear is protectivefootwear that complies to an ASTM standard with a specific7.1 The marking as defined in this specification indicatesyear of issuance.that the protective footwear bearing this label meets theminimum requirements for the product category as definedASTM
25、F241311(ASTM Standard No.)】(Year of issuance)】within this specification.6.1.4 Line 2 of label shall identify the appropriate gender7.2 Responsibility of the Manufacturer or Supplier-Theand the impact and compression rating of the category.manufacturer or supplier,or both,of the protective footwearM/
26、75/C75bearing the marking shall maintain documentation to identifyM75c75the product category sampled for testing,a report of testsMaleImpactImpactCompressionCompressionperformed,test results,date of testing,and identity of theResistantRatingResistantRatingFootwearFootwearindependent testing facility
27、 used.7.2.1 Responsibility of Testing Facility-The independenttesting facility of record shall maintain verifiable documenta-TABLE 1 Examples of Marking and Identificationtion to identify the product category of protective footwearIdentificationDescriptionsampled for testing a report of test perform
28、ed,test results,dateExample Atested,and the manufacturer or supplier,or both,of the productASTM F2413-11 Protective footwear that complies with thecategory tested.performance requirement of F2413 issuedin2011.7.3 Compliance Requirements-The manufacturer orLine 2FV75/C75Footwear worn by female worker
29、 which hassupplier,or both,of protective footwear bearing the markingImpact 75 resistance and Compression 75resistancelabel that is found to be in non-compliance with the require-Line 3EHElectrical hazard resistant footwear.ments of this specification is liable for immediate disqualifi-Example Bcati
30、on from using the ASTM label for that product category.Line 1ASTM F2413-11 Protective footwear that complies with theperformance requirement of F2413 issued8.Keywordsin2011.Line 2M75/C/75Footwear worn by male worker which has8.1 C compression resistance;CD conductive footwear;EHImpact 75 resistance and Compression 75electric hazard resistance;ESD:foot protection:I impactresistance.Line 3CdFootwear is conductive.resistance;Mt metatarsal protection;protective footwear;PRpuncture resistance;safety footwear;SD static dissipative
