1、Designation:F216719Standard Consumer Safety Specification forInfant Bouncer Seats1This standard is issued under the fixed designation F2167;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenth
2、eses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification is intended to minimize the risk of injury or death associatedwith a childs use of an infant bouncer seat.The specific h
3、azards addressed by this specification areproduct disassembly/collapse,stability,and falls from elevated surfaces.1.Scope1.1 This consumer safety specification covers establishmentof requirements,test methods,and marking requirements topromote safe use of an infant bouncer seat by an occupant anda c
4、aregiver.1.2 For purposes of this consumer safety specification,aninfant bouncer seat is a freestanding product intended tosupport an occupant in a reclined position to facilitate bouncingby the occupant,with the aid of a caregiver or by other means.Intended occupants are infants who have not develo
5、ped theability to sit up unassisted(approximately 0 to 6 months ofage).1.3 This consumer safety specification is intended to mini-mize the risk of injury to an occupant resulting from normaluse and reasonably foreseeable misuse or abuse of an infantbouncer seat.1.4 No infant bouncer seat produced af
6、ter the approval dateof this consumer safety specification shall,either by label orother means,indicate compliance with this specification unlessit conforms to all requirements contained herein.1.5 This consumer safety specification is not intended toaddress incidents and injuries resulting from the
7、 interaction ofother persons with the occupant in an infant bouncer seat or theincidents resulting from abuse or misuse by other children.1.6 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided
8、for information onlyand are not considered standard.1.7 The following precautionary caveat pertains only to thetest method portion,Section 7,of this consumer safety speci-fication:This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibili
9、ty of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory requirements prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization est
10、ablished in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Rating Adhesion by Tape TestF404 Consumer
11、Safety Specification for High ChairsF963 Consumer Safety Specification for Toy SafetyF2050 Consumer Safety Specification for Hand-Held InfantCarriers2.2 Federal Regulations:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500.48 Technical Re
12、quirements for Determining aSharp Point in Toys or Other Articles Intended for Use byChildren Under Eight Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys or Other ArticlesIntended for Use by Children Under Eight Years of Age16 CFR 1500.50-.51 Test
13、 Methods for Simulating Use andAbuse of Toys and Other Articles Intended for Use byChildren1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct responsibility of Subcommittee F15.21 onInfant Carriers,Bouncers and Baby Swings.Current edition approv
14、ed May 1,2019.Published June 2019.Originallyapproved in 2001.Last previous edition approved in 2017 as F2167 17.DOI:10.1520/F2167-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informati
15、on,refer to the standards Document Summary page onthe ASTM website.3Code of Federal Regulations,available from U.S.Government Printing Office,732 North Capitol St.,NW,Mail Stop:SDE,Washington DC 20401.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Unit
16、ed StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 16 CFR 1501 Method for Identifying Toys and Other Ar-ticles Intended for Use by Children Under Three Years ofAge Which Present Choking,Aspiration or IngestionHazards Because o
