收藏 分享(赏)

ASTM_F_2431_-_04_2012.pdf

上传人:益****师 文档编号:191580 上传时间:2023-03-04 格式:PDF 页数:4 大小:88.04KB
下载 相关 举报
ASTM_F_2431_-_04_2012.pdf_第1页
第1页 / 共4页
ASTM_F_2431_-_04_2012.pdf_第2页
第2页 / 共4页
ASTM_F_2431_-_04_2012.pdf_第3页
第3页 / 共4页
ASTM_F_2431_-_04_2012.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F243104(Reapproved 2012)Standard Specification forRing Bearing,Inner:For Needle Roller Bearing with ThickOuter Ring1This standard is issued under the fixed designation F2431;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision

2、,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers

3、 inner rings for needle rollerbearings having thick outer rings.1.2 The inner rings being specified are intended for use onunhardened shafts in conjunction with the MS51961 needleroller bearings specified in Specification F2246.1.2.1 For needle roller bearings with thin outer rings(Speci-fication F2

4、162,MS17131,MS52141)use inner rings specifiedin Specification F2163.1.3 Inner rings designed to this specification are intendedfor use in applications requiring high radial load with minimalangular shaft misalignment.1.4 The values stated in inch-pound units are to be regardedas standard.The values

5、given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This specification contains many of the requirements ofMS51962,which was originally developed by the Departmentof Defense and maintained by the Defense Supply Center

6、 inRichmond.The following government activity codes may befound in the Department of Defense,Standardization DirectorySD-1.2Preparing activityCustodiansReview ActivityDLAGS4Army ATAir Force84NavyOSAir Force-992.Referenced Documents2.1 ASTM Standards:3E18 Test Methods for Rockwell Hardness of Metalli

7、c Ma-terialsF2162 Specification for Bearing,Roller,Needle:DrawnOuter Ring,Full Complement,Without Inner Ring,Openand Closed End,Standard TypeF2163 Specification for Ring,Bearing,Inner:for NeedleRoller Bearing With Drawn Outer RingF2246 Specification for Bearing,Roller,Needle:ThickOuter Ring With Rol

8、lers and Cage2.2 ANSI Standard:4ASMEB46.1 SurfaceTexture(SurfaceRoughness,Waviness,and Lay)2.3 SAE Standards:5SAE J404 Chemical Compositions of SAE Alloy SteelsSAE AMSSTD66 Steel:Chemical Composition and Hard-enability2.4 Military Standard.6MIL-STD-130 Identification Marking of U.S.Military Prop-ert

9、yMIL-STD-197 Packaging of Bearings,Associated Parts andSubassemblies2.5 ABMA Standards:7ABMA 4 Tolerance Definitions and Gauging Practices forBall and Roller BearingsABMA 18.2 Needle Roller Bearings Radial,Inch Design2.6 ISO Standard:4ISO 5593 Rolling BearingsVocabulary1This specification is under t

10、he jurisdiction ofASTM Committee F34 on RollingElement Bearings and is the direct responsibility of Subcommittee Automotive/Industrial Bearing.Current edition approved Dec.1,2012.Published January 2013.Originallyapproved in 2004.Last previous edition approved in 2004 as F243104.DOI:10.1520/F2431-04R

11、12.2The Military codes that are listed in SD-1 give the address and phone numbersof the DoD contacts.These are found in the DoDs ASSIST website,http:/assist.daps.dla.mil/online/start/.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.or

12、g.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from SAE International(SAE),400 Commonwealth Dr.,W

13、arrendale,PA 15096-0001,http:/www.sae.org.6Available on the DODs ASSIST website,http:/assist.daps.dla.mil/online/start/.7Available from Techstreet,3916 Ranchero Drive,Ann Arbor,MI,48108,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United State

14、s1 3.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to ABMA STD 4 and ISO 5593.4.Ordering Information4.1 Whenorderingpartsinaccordancewiththisspecification,specify the following:TABLE 1 Inner Ring DimensionsDashNumberdBore Diameter,in.FOutside Diameter,in.BWidth,i

15、n.+0.000,-0.005rRadius,in.(see7.3)MatingBearingMS51961Dash Number(seeSpecificationF2246)Nom.Min.Max.Nom.Min.Max.-1380.37460.3750580.62410.62450.7600.025-1-2120.49960.5000340.74880.74930.7600.040-2-3120.49960.5000340.74880.74931.0100.040-3-4580.62460.6250780.87380.87430.7600.040-5-5340.74960.750010.9

16、9880.99930.7600.040-8-613160.81200.812510.99880.99930.7600.040-8-713160.81200.812510.99880.99931.0100.040-9-8780.87450.87501181.12361.12411.0100.040-11-915160.93700.93751181.12361.12411.0100.040-11-1010.99951.00001141.24851.24911.0100.040-14-1110.99951.00001141.24851.24911.2600.040-15-121181.12451.12501381.37351.37411.0100.040-18-131181.12451.12501381.37351.37411.2600.040-19-1413161.18701.18751121.49841.49901.2600.060-22-151141.24951.25001121.49841.49901.0100.060-21-161141.24951.25001121.49841.4

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2