收藏 分享(赏)

ASTM_F_2206_-_14.pdf

上传人:益****师 文档编号:191761 上传时间:2023-03-04 格式:PDF 页数:5 大小:89.55KB
下载 相关 举报
ASTM_F_2206_-_14.pdf_第1页
第1页 / 共5页
ASTM_F_2206_-_14.pdf_第2页
第2页 / 共5页
ASTM_F_2206_-_14.pdf_第3页
第3页 / 共5页
ASTM_F_2206_-_14.pdf_第4页
第4页 / 共5页
ASTM_F_2206_-_14.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F220614Standard Specification forFabricated Fittings of Butt-Fused Polyethylene(PE)1This standard is issued under the fixed designation F2206;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num

2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification establishes requirements for fabri-cated fittings intended for use with outside-diameter controlledpolyethylene pipe and t

3、ubing.These fittings are manufacturedby heat-fusion joining shape-modified polyethylene compo-nents prepared from pipe,molded fittings,sheet,billet,orblock.Included are requirements for materials,design,workmanship,minimum dimensions,marking,test methods,and quality control.1.2 Pressure rating of th

4、e fabricated-fitting design is beyondthe scope of this standard and shall be established by the fittingmanufacturer.This specification includes requirements for bothelevated temperature pressure-tests and short-term pressuriza-tion tests to demonstrate a reasonable level of performance ofthe fabrica

5、ted-fitting design at the pressure rating establishedby the fitting manufacturer.1.3 The pressure-tests requirements are specified by thefittingsequivalent(E)DR.The EDR specified is the DR of thepiping system for which the fabricated fitting is intended to bebutt-fused.1.4 The text of this standard

6、references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.5 UnitsThe values stated in inch-pound units are to beregarded as standard.The values given in parentheses aremath

7、ematical conversions to SI units which are provided forinformation only and are not considered standard.1.6 The following safety hazards caveat pertains only to thetest methods portion,Section 9,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associat

8、ed with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122

9、 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2513 Specification for Polyethylene(PE)Gas PressurePipe,Tubing,and FittingsD3035 Specification for Polyethylene(PE)Plastic Pipe(DR-PR)Based on Controlled Outside DiameterD3261 Specification for Butt Heat Fusion Polyethylene(

10、PE)Plastic Fittings for Polyethylene(PE)Plastic Pipe andTubingF412 Terminology Relating to Plastic Piping SystemsF714 Specification for Polyethylene(PE)Plastic Pipe(DR-PR)Based on Outside DiameterF2619/F2619M Specification for High-Density Polyethylene(PE)Line PipeF2880 Specification For Lap-Joint T

11、ype Flange Adapters forPolyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in.to 65 in.F3034 Specification for Billets made by Winding MoltenExtruded Stress-Rated High Density Polyethylene(HDPE)2.2 Federal Standards:3Fed.Std.No.123 Marking for Shipment(Civil Agencies)OPS Part 192 Title 49,Code of F

12、ederal Regulations2.3 Military Standard:3MIL-STD-129 Marking for Shipment and Storage2.4 ANSI/NSF Standard:4ANSI/NSF 61 for Drinking Water System ComponentsHealth Effects2.5 Plastic Pipe Institute:5TR-4 Listing of Hydrostatic Design Basis(HDB),Hydro-static Design Stress(HDS),Strength Design Basis(SD

13、B),1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Dec.1,2014.Published January 2015.Originallyapproved in 2002.Last previous edition approved in 2011 as F2206 11

14、.DOI:10.1520/F2206-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3DLA Document Services Building 4/D 700 Robb

15、ins Avenue Philadelphia,PA19111-5094 http:/quicksearch.dla.mil/4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from Plastics Pipe Institute(PPI),105 Decker Court,Suite 825,Irving,TX 75062,http:/www.plasticpipe.org.*A

16、 Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 Pressure Design Basis(PDB)and Minimum RequiredStrength(MRS)for Thermoplastic Materials or Pipe.3.Terminology3.1 Definitions are in accordance with Terminology F412and abbreviations are in accordance with Terminology D1600,unless otherwise specified.3.2 Definitions:3.2.1 butt-fusion end(s),nthe butt end(s)of the fabricatedfitt

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2