1、Designation:F166717Standard Specification forDriven Fasteners:Nails,Spikes,and Staples1This standard is issued under the fixed designation F1667;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pa
2、rentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.The Commercial and Government Entity(Cage)Code for ASTM:81346.1.Scope*1.1 Thi
3、s specification covers nails,spikes,staples,and otherdriven fasteners,as listed in Table 1.NOTE1Fastener ductility information is presented in Table 2 anddimensional information in Tables 365.1.2 Fasteners described in this specification are driven byhand tool,power tool,or mechanical device in sing
4、le ormultiple strikes and are positioned by hand,tool,or machine.1.3 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard.1.4 Fasteners in this specification are sold in bulk(loose)form and are collated for loading into the ma
5、gazine of anapplication tool.Other than as covered in Section 9,Workmanship,cohering materials(including,but not limitedto,plastic,adhesive bond,paper tape,plastic strip,plasticcarrier,wire,etc.)and relative orientation of collated fastenersare not within the scope of this standard.1.5 This standard
6、 does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.6 This international standard was
7、 developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Do
8、cuments2.1 ASTM Standards:2A153/A153M Specification for Zinc Coating(Hot-Dip)onIron and Steel HardwareA510/A510M Specification for General Requirements forWire Rods and Coarse Round Wire,Carbon Steel,andAlloy SteelA641/A641M Specification for ZincCoated(Galvanized)Carbon Steel WireB695 Specification
9、 for Coatings of Zinc Mechanically De-posited on Iron and SteelC514 Specification for Nails for the Application of GypsumBoard3F547 Terminology of Nails for Use with Wood and Wood-Base MaterialsF592 Terminology of Collated and Cohered Fasteners andTheir Application Tools(Withdrawn 2017)4F680 Test Me
10、thods for NailsF1575 Test Method for Determining Bending Yield Momentof Nails3.Terminology3.1 DefinitionsThe definitions used in this specificationare those of common commercial acceptance and usage andalso appear in Terminologies F547 and F592.4.Classification4.1 The fasteners and their Table 1 cla
11、ssification are iden-tified as follows:1This specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.05 on Driven andOther Fasteners.Current edition approved March 1,2017.Published April 2017.Originallyapproved in 1995.Last previ
12、ous edition approved in 2015 as F1667 15.DOI:10.1520/F1667-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Add
13、itional material and dimensional tolerance for nails used in Gypsumboardare addressed in C514.4The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box
14、 C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the Wo
15、rld Trade Organization Technical Barriers to Trade(TBT)Committee.1 NOTE2The identification of fasteners,classified by style and type(alpha indicators)followed by a dash number(numerical code)based onTables 362,identifies dimensions specifically and establishes a PIN(partidentifying number)system whe
16、n preceded by the F1667 ASTM desig-nator of this specification.For example:4.2 The trade designation,S,pennyweight,used in commer-cial practice is referenced in Tables 347 wherever it applies.5.Ordering Information5.1 Orders for driven fasteners under this specification shallinclude the following information:5.1.1 Quantity or weight;5.1.2 Part identifying number(PIN)or product description(see 4.1 and appropriate table);5.1.3 Special material requirements,if specified,includingcoatings or finishe
