1、 INTERNATIONAL STANDARD IEC61019-1 First edition2004-11 Surface acoustic wave(SAW)resonators Part 1:Generic specification Reference number IEC 61019-1:2004(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.Publication numbering As from
2、 1 January 1997 all IEC publications are issued with a designation in the 60000 series.For example,IEC 34-1 is now referred to as IEC 60034-1.Consolidated editions The IEC is now publishing consolidated versions of its publications.For example,edition numbers 1.0,1.1 and 1.2 refer,respectively,to th
3、e base publication,the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2.Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC,thus ensuring that the content reflects current techn
4、ology.Information relating to this publication,including its validity,is available in the IEC Catalogue of publications(see below)in addition to new editions,amendments and corrigenda.Information on the subjects under consideration and work in progress undertaken by the technical committee which has
5、 prepared this publication,as well as the list of publications issued,is also available from the following:IEC Web Site(www.iec.ch)Catalogue of IEC publications The on-line catalogue on the IEC web site(www.iec.ch/searchpub)enables you to search by a variety of criteria including text searches,techn
6、ical committees and date of publication.On-line information is also available on recently issued publications,withdrawn and replaced publications,as well as corrigenda.IEC Just Published This summary of recently issued publications(www.iec.ch/online_news/justpub)is also available by email.Please con
7、tact the Customer Service Centre(see below)for further information.Customer Service Centre If you have any questions regarding this publication or need further assistance,please contact the Customer Service Centre:Email:custserviec.ch Tel:+41 22 919 02 11 Fax:+41 22 919 03 00 LICENSED TO MECON Limit
8、ed.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.INTERNATIONAL STANDARD IEC61019-1 First edition2004-11 Surface acoustic wave(SAW)resonators Part 1:Generic specification IEC 2004 Copyright-all rights reserved No part of this publication may be reproduced or u
9、tilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from the publisher.International Electrotechnical Commission,3,rue de Varemb,PO Box 131,CH-1211 Geneva 20,SwitzerlandTelephone:+41 22 919 02 11 Telefax:+41 22 919 03 00 E-m
10、ail:inmailiec.ch Web:www.iec.ch W For price,see current cataloguePRICE CODE Commission Electrotechnique InternationaleInternational Electrotechnical Commission LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 61019-1 IEC:2004(E)CONTEN
11、TS FOREWORD.4 1 Scope.6 2 Normative references.6 3 Order of precedence.8 4 Terms and definitions.8 4.1 General terms.8 4.2 Operational properties.11 5 Preferred values for ratings and characteristics.19 5.1 Standard nominal frequency values in megahertz(MHz).19 5.2 Standard operating temperature ran
12、ges in degrees Celsius(C).19 5.3 Standard values of load capacitance in picofarads(pF).19 5.4 Standard levels of drive in milliwatts(mW).19 5.5 Standard values of minimum insertion attenuation in decibels(dB).19 5.6 Standard climatic category.20 5.7 Bump severity.20 5.8 Vibration severity.20 5.9 Sho
13、ck severity.20 5.10 Fine leak rate.21 6 Marking.21 6.1 Resonator marking.21 6.2 Package marking.21 7 Quality assessment procedures.21 7.1 Primary stage of manufacture.21 7.2 Structurally similar components.21 7.3 Subcontracting.22 7.4 Incorporated components.22 7.5 Manufacturers approval.22 7.6 Appr
14、oval procedures.22 7.7 Procedures for capability approval.23 7.8 Procedures for qualification approval.23 7.9 Test procedures.24 7.10 Screening requirements.24 7.11 Rework and repair work.24 7.12 Certified records of released lots.24 7.13 Validity of release.24 7.14 Release for delivery.24 7.15 Unch
15、ecked parameters.24 8 Test and measurement procedures.24 8.1 General.24 8.2 Test and measurement conditions.25 8.3 Visual inspection.26 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.61019-1 IEC:2004(E)3 8.4 Dimensions and gauging pro
16、cedures.26 8.5 Measurement method of one-port resonator.26 8.6 Measurement method of two-port resonator.28 8.7 Mechanical and environmental test procedures.32 8.8 Endurance test procedure.37 Figure 1 Basic configurations of SAW resonators.9 Figure 2 One-port resonator equivalent circuit.12 Figure 3 Vector admittance diagram of a one-port SAW resonator.14 Figure 4 Typical frequency characteristics of a one-port SAW resonator inserted into a transmission line in series(see 4.2.10.2.1 and 4.2.10.3.
