1、 IEC 60286-2Edition 3.0 2008-03INTERNATIONAL STANDARD Packaging of components for automatic handling Part 2:Packing of components with unidirectional leads on continuous tapes IEC 60286-2:2008(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY
2、 BUREAU.THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC,Geneva,Switzerland All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission
3、in writing from either IEC or IECs member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,please contact the address below or your local IEC member National Committee for further
4、 information.IEC Central Office 3,rue de Varemb CH-1211 Geneva 20 Switzerland Email:inmailiec.ch Web:www.iec.ch About the IEC The International Electrotechnical Commission(IEC)is the leading global organization that prepares and publishes International Standards for all electrical,electronic and rel
5、ated technologies.About IEC publications The technical content of IEC publications is kept under constant review by the IEC.Please make sure that you have the latest edition,a corrigenda or an amendment might have been published.?Catalogue of IEC publications:www.iec.ch/searchpub The IEC on-line Cat
6、alogue enables you to search by a variety of criteria(reference number,text,technical committee,).It also gives information on projects,withdrawn and replaced publications.?IEC Just Published:www.iec.ch/online_news/justpub Stay up to date on all new IEC publications.Just Published details twice a mo
7、nth all new publications released.Available on-line and also by email.?Electropedia:www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French,with equivalent terms in additional languages.Also
8、known as the International Electrotechnical Vocabulary online.?Customer Service Centre:www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance,please visit the Customer Service Centre FAQ or contact us:Email:csciec.ch Tel.:+41 22 919 02 11 Fax
9、:+41 22 919 03 00 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.IEC 60286-2Edition 3.0 2008-03INTERNATIONAL STANDARD Packaging of components for automatic handling Part 2:Packing of components with unidirectional leads on continuous
10、tapes INTERNATIONAL ELECTROTECHNICAL COMMISSION VICS 31.020;31.240 PRICE CODEISBN 2-8318-9546-4 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 60286-2 IEC:2008(E)CONTENTS FOREWORD.5 1 General.7 1.1 Scope.7 1.2 Normative references.7
11、 2 Terms and definitions.7 3 Dimensions.8 3.1 Dimensions common to tapes and taped components.8 3.1.1 Coordinate system.8 3.1.2 Tape width.9 3.1.3 Pitches of components and sprocket holes.9 3.1.4 Dimensions of either components position from abscissa.10 3.1.5 Diameter d of lead terminal and tape thi
12、ckness.11 3.1.6 Maximum permissible deviation.12 3.1.7 Maximum permissible protrusion of the ends of the leads(see Figure 2).12 3.2 Dimensions common to tapes and taped components with two leads.12 3.2.1 Lead spacing F of components.12 3.2.2 Tolerance on lead spacing F.12 3.3 Dimensions common to ta
13、pes and taped components with three leads.13 3.3.1 Lead spacing F1 and F2 of components.13 3.3.2 Tolerance on lead spacing F1 and F2.13 3.3.3 Distance P2.13 3.4 Dimensions common to tapes and taped components with short terminal without tape.13 3.4.1 Type of taping with short terminal without tape.1
14、3 3.4.2 Distance H2.14 3.4.3 Distance K.14 3.4.4 Diameter d1 of short terminal without tape.14 3.4.5 Position and tolerance of short terminal without tape.15 4 Taping.15 4.1 Dimensions of taping.15 4.2 Splices.15 4.3 Leader and trailer of tape.15 5 Performance of tape.16 5.1 Polarity direction on ta
15、pe.16 5.2 Kinks or bends on tape.16 5.3 Pull strength from taping and peel strength of cover tape.16 5.4 Break force of tape.17 5.5 Material of tape.17 5.6 Hold-down tape.17 5.7 Storage.17 5.8 Missing components.17 6 Packing.18 6.1 Dimensions of the reel.18 6.1.1 Protection of components.20 6.1.2 Re
16、el filling.20 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60286-2 IEC:2008(E)3 6.2 Dimensions of the fan-fold container.20 6.3 Recycling.20 6.4 Marking.20 Annex A(informative)Dimensions for two formed leads,sprocket hole between parts.22 Annex B(informative)Dimensions for two formed leads,sprocket hole between leads.24 Annex C(informative)Dimensions for two straight leads,sprocket hole between parts.26 Annex D(informative)Dimen
