1、NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2AMENDEMENT 8AMENDMENT 82003-06CODE PRIXPRICE CODEPour prix,voir catalogue en vigueurFor price,see current catalogueJAmendement 8Normalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsAmendment 8Mechanical standardization of semi
2、conductordevices Part 2:DimensionsLes feuilles de cet amendement sont insrer dans laPublication 60191-2The sheets contained in this amendment are to beinserted in Publication 60191-2LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICEN
3、SED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2 Amend.8 CEI/IEC:2003INSTRUCTIONS POUR LINSERTION DESNOUVELLES PAGES DANS LA CEI 60191-2Remplacer la page de titre existante par lanouvelle page de titre.Retirer la page 60191 IEC I exi
4、stantecontenant la prface et la remplacer par lanouvelle page 60191 IEC I contenant laprface lamendment 8(2003).Chapitre I:Ajouter les nouvelles feuilles suivantes:60191 IEC I-166E-a/b/c/d/e/f/g/h/i/j/kINSTRUCTIONS FOR THE INSERTIONOF NEW PAGES IN IEC 60191-2Replace the existing title page with the
5、new titlepage.Remove the existing page 60191 IEC Icontaining the preface and insert in its place thenew page 60191 IEC I containing the preface toAmendment 8(2003).Chapter I:Add the following new sheets:60191 IEC I-166E-a/b/c/d/e/f/g/h/i/j/kLICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE
6、 AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2Premire ditionFirst edition1966Modifie selon les Complments:Amended in accordanc
7、e with Supplement:A(1967),B(1969),C(1970),D(1971),E(1974),F(1976),G(1978),H(1978),J(1980),K(1981),L(1982),M(1983),N(1987),P(1988),Q(1990),R(1995),S(1995),T(1995),U(1997),V(1998),W(1999),X(1999),Y(2000),Z(2000)et/and Amendement/Amendment 1(2001),2(2001),3(2001),4(2001),5(2002),6(2002),7(2002),8(2003)
8、Normalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsMechanical standardization of semiconductordevices Part 2:Dimensions IEC 2003 Droits de reproduction rservs Copyright-all rights reservedAucune partie de cette publication ne peut tre reproduiteni utilise sous quelque forme qu
9、e ce soit et par aucunprocd,lectronique ou mcanique,y compris la photo-copie et les microfilms,sans laccord crit de lditeur.No part of this publication may be reproduced or utilized inany form or by any means,electronic or mechanical,including photocopying and microfilm,without permissionin writing
10、from the publisher.International Electrotechnical Commission,3,rue de Varemb,PO Box 131,CH-1211 Geneva 20,SwitzerlandTelephone:+41 22 919 02 11 Telefax:+41 22 919 03 00 E-mail:inmailiec.ch Web:www.iec.chCommission Electrotechnique InternationaleInternational Electrotechnical Commission LICENSED TO M
11、ECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.COMMISSION LECTROTECHNIQUEINTERNATIONALEINTERNATIONALELECTROTECHNICAL COMMISSIONPUBLICA
12、TION 191-2PUBLICATION 191-2NORMALISATION MCANIQUEDES DISPOSITIFS SEMICONDUCTEURSDEUXIME PARTIE:DIMENSIONSMECHANICAL STANDARDIZATIONOF SEMICONDUCTORDEVICESPART 2:DIMENSIONSSOMMAIREPRAMBULEPRFACECONCEPTION DE LA NORMALISATIONMCANIQUE.Chapitre 00VALEURS RECOMMANDES POUR CER-TAINES DIMENSIONS DE DESSINS
13、 DE DISPOSITIFS SEMICONDUCTEURS.Chapitre 0DESSINS DENCOMBREMENTS.Chapitre ITYPES DE DISPOSITIFS SEMICONDUC-TEURS GNRALEMENT MONTSDANS LES BOTIERS DU CHAPITRE IDESSINS DEMBASES.Chapitre IIDESSINS DE BOTIERS.Chapitre IIIDESSINS DE CALIBRES.Chapitre IVTABLEAUX MONTRANT LES ASSOCIA-TIONS ENTRE LES BOTIE
14、RS ET LESEMBASES.Chapitre VDESSINS OBSOLTESCOMPLMENTS AUX LISTES DE CODESNATIONAUX FIGURANT SUR LESFEUILLES DES NORMES DELA PUBLICATION 191-2 DE LA CEISUPPRESSIONS DANS LES LISTESDE CODES NATIONAUX FIGURANTSUR LES FEUILLES DE NORMES DELA PUBLICATION 191-2 DE LA CEICONTENTSFOREWORDPREFACEPHILOSOPHY O
15、F MECHANICAL STAN-DARDIZATION.Chapter 00RECOMMENDED VALUES FOR CERTAINDIMENSIONS OF DRAWINGS OF SEMI-CONDUCTOR DEVICES.Chapter 0DEVICE OUTLINE DRAWINGS.Chapter ITYPES OF SEMICONDUCTOR DEVICESGENERALLY MOUNTED IN THEPACKAGES OF CHAPTER IBASE DRAWINGS.Chapter IICASE OUTLINE DRAWINGS.Chapter IIIGAUGE D
16、RAWINGS.Chapter IVTABLES SHOWING ASSOCIATIONS BE-TWEEN CASE OUTLINES AND BASES.Chapter VOBSOLETE DRAWINGSADDITIONS TO THE LISTS OFNATIONAL CODES APPEARING ONTHE STANDARD SHEETS OFIEC PUBLICATION 191-2DELETIONS TO THE LISTS OFNATIONAL CODES APPEARING ONTHE STANDARD SHEETS OFIEC PUBLICATION 191-2Publication CEI 191-2Date:1987IEC Publication 191-2Date:1987LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2 amend.8 CEI/IEC:2003COMM
