1、 INTERNATIONAL STANDARD IEC60371-3-7 1995AMENDMENT 12006-09 Amendment 1 Insulating materials based on mica Part 3:Specifications for individual materials Sheet 7:Polyester film mica paper with an epoxy resin binder for single conductor taping PRICE CODE IEC 2006 Droits de reproduction rservs Copyrig
2、ht-all rights reserved International Electrotechnical Commission,3,rue de Varemb,PO Box 131,CH-1211 Geneva 20,SwitzerlandTelephone:+41 22 919 02 11 Telefax:+41 22 919 03 00 E-mail:inmailiec.ch Web:www.iec.ch D For price,see current catalogueCommission Electrotechnique InternationaleInternational Ele
3、ctrotechnical Commission LICENSED TO MECON Limited.-RANCHI/BANGALORE,FOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 60371-3-7 Amend.1 IEC:2006(E)FOREWORD This amendment has been prepared by IEC technical committee 15:Standards on specifications for electrical insulating mate
4、rials.The text of this amendment is based on the following documents:FDIS Report on voting 15/334/FDIS 15/349/RVD Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table.The committee has decided that the contents of this am
5、endment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under http:/webstore.iec.ch in the data related to the specific publication.At this date,the publication will be reconfirmed,withdrawn,replaced by a revised edition,or amended._ Pag
6、e 5 INTRODUCTION Replace the existing text by the following new text:This International Standard is one of a series which deals with insulating materials for use in electrical equipment built up from mica splittings or mica paper,with or without reinforcement,and with mica paper in its pure state.Th
7、e series consists of the following three parts:Part 1:Definitions and general requirements(IEC 60371-1)Part 2:Methods of test(IEC 60371-2)Part 3:Specifications for individual materials(IEC 60371-3)This standard contains one of the sheets comprising part 3,as follows:Sheet 7:Polyester film mica paper
8、 with an epoxy resin binder for single conductor taping.LICENSED TO MECON Limited.-RANCHI/BANGALORE,FOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60371-3-7 Amend.1 IEC:2006(E)3 Page 7 1 Scope Insert the following paragraph after the existing paragraphs:Safety warning:It is th
9、e responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.2 Normative references Replace the existing references by the following new references:IEC 60243-1:1998,Electric strength of insulating materials Test methods Part 1:Te
10、sts at power frequencies IEC 60371-2:2004,Specification for insulating materials based on mica Part 2:Methods of test IEC 60371-3-2:2005,Insulating materials based on mica Part 3:Specifications for individual materials Sheet 2:Mica paper IEC 60674-3-2:1992,Specification for plastic films for electri
11、cal purposes Part 3:Specifications for individual materials Sheet 2:Requirements for balanced biaxially oriented polyethylene terephthalate(PET)films used for electrical insulation Page 9 3 Designation Replace the existing first two paragraphs by the following new paragraphs:When ordering materials
12、to this specification,only the specification and type numbers need be quoted(see Table 1).Example:IEC 60371-3-7:type 7.1.01 The type number is derived from:the specification sheet number 7 followed by the sheet table number 1 followed by the number of the product in the sheet table 01 Thus giving ty
13、pe number 7.1.01.The final paragraph and table remain unchanged.LICENSED TO MECON Limited.-RANCHI/BANGALORE,FOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.4 60371-3-7 Amend.1 IEC:2006(E)4.1 Mica paper Replace the text of this subclause by the following new text:Mica paper refe
14、rred to in this specification shall comply with the requirements of IEC 60371-3-2.4.2 Polyester film Replace the text of this subclause by the following new text:Plastic films used as backing material shall be made from PET and shall comply with the requirements of IEC 60674-3-2.5 Requirements:compo
15、sitions and tolerances Replace the text of this clause by the following new text:When tested by the method of Clause 7 of IEC 60371-2,the composition of the products shall lie within the limits of Table 1.Page 11 6.3 Thickness Replace the first sentence of this subclause by the following new sentenc
16、e:Measure the thickness in accordance with Clause 4 of IEC 60371-2,using the apparatus given in 4.1.1 of that standard,making 10 measurements of one thickness of material.Page 13 6.7 Stiffness Replace the second sentence of this subclause by the following new sentence:When the stiffness is specified,the material should be tested by the method of Clause 11 in IEC 60371-2.6.8 Electric strength Replace the text of this subclause by the following new text:When tested by the method of Clause 16 of IE
