1、 Reference numberISO/IEC 22536:2013(E)ISO/IEC 2013 INTERNATIONAL STANDARD ISO/IEC22536Second edition2013-01-15 Information technology Telecommunications and information exchange between systems Near Field Communication Interface and Protocol(NFCIP-1)RF interface test methods Technologies de linforma
2、tion Tlcommunications et change dinformation entre systmes Interface et protocole de communication en champ proche(NFCIP-1)Mthodes dessai pour interface RF ISO/IEC 22536:2013(E)COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2013 All rights reserved.Unless otherwise specified,no part of this publication may be
3、 reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 7
4、49 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2013 All rights reserved ISO/IEC 22536:2013(E)ISO/IEC 2013 All rights reserved iii Contents Page Foreword.v1 Scope.12 Conformance.13 Normative references.14 Conventions and notations.14.1 Repres
5、entation of numbers.14.2 Names.24.3 Test report.25 Abbreviations and acronyms.26 Default items applicable to the test methods.26.1 Test environment.26.2 Default tolerance.26.3 Spurious Inductance.26.4 Total measurement uncertainty.26.5 Antenna class.27 Test Set-up and test circuits.37.1 Digital samp
6、ling oscilloscope.37.2 Calibration coil.37.3 Test assembly.37.4 Reference Device.37.4.1 Dimensions of the Reference Device.37.4.2 Reference Device construction.37.4.3 Reference Device resonance frequency tuning.48 Functional Test Initiator.48.1 Initiator RF field detection.48.1.1 Purpose.48.1.2 Test
7、 procedure.48.1.3 Test report.48.2 Initiator field strength in active and passive communication mode.48.2.1 Purpose.48.2.2 Test procedure.58.2.3 Test report.58.3 Initiator modulation index and waveform transmission in active and passive communication mode.58.3.1 Purpose.58.3.2 Test procedure.58.3.3
8、Test report.58.4 Initiator load modulation reception in passive communication mode.58.4.1 Purpose.58.4.2 Test procedure.58.4.3 Test report.58.5 Initiator modulation index and waveform reception in active communication mode.58.5.1 Purpose.58.5.2 Bit rate of 106 kbit/s.58.5.3 Bit rates of 212 kbit/s a
9、nd 424 kbit/s.68.6 Initiator maximum loading effect test in active communication mode(Optional).68.6.1 Purpose.68.6.2 Test procedure.6ISO/IEC 22536:2013(E)iv ISO/IEC 2013 All rights reserved 8.6.3 Test report.69 Functional Test Target.69.1 Target load modulation transmission in passive communication
10、 mode.69.1.1 Purpose.69.1.2 Test procedure.79.2 Target field strength in active communication mode.79.3 Target modulation index and waveform transmission in active communication mode.79.4 Target modulation index and waveform reception in active and passive communication mode.79.5 Target maximum load
11、ing effect test in Passive communication mode(Optional).7Annex A(informative)Test report template example.8 ISO/IEC 22536:2013(E)ISO/IEC 2013 All rights reserved v Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specializ
12、ed system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committe
13、es collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.International Standards
14、 are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of the joint technical committee is to prepare International Standards.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an
15、International Standard requires approval by at least 75%of the national bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.E
16、cma International purposefully aligned this International Standard with ISO/IEC 10373-6 to allow testing laboratories to reuse equipment and expertise.ISO/IEC 22536:2013 was prepared jointly by Joint Technical Committee ISO/IEC JTC 1,Information technology,Subcommittee SC 6,Telecommunications and information exchange between systems.This second edition cancels and replaces the first edition(ISO/IEC 22536:2005),which has been technically revised.INTERNATIONAL STANDARD ISO/IEC 22536:2013(E)ISO/IEC
