1、 -W 9009275 0024037 737 W A M E R I C A N N A T I O N A L S T A N D A R D Carbide Blanks and Sing le-Point Brazed Tools ANSI B94.5-1974(REVISION OF ANSI 094.5-1966)SECRETA R I A 1 THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E
2、N G I N E E R S United Engineering Center New York,N.Y.1001 7 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without
3、license from IHS-,-,-m 9009275 0024038 673 m No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright 1974 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in U.S.A.Copyright ASME Inte
4、rnational Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-m 9009275 0024039 SOT m FOREWORD This standard was initially a part of American S
5、tandard Single Point Tools and Tool Posts ASA R5.22-1950.Revision of the Carbide tooling portion of B5.22-1950 resulted in the recommendation for a standard covering Carbide Blanks and Cutting Tools.Technical Committee TC-2 of B5 was organized for this purpose,and the standard was reviewed and revis
6、ed.The standard was ap-proved and designated ASA B5.36,November 18,1957.Requests from manufacturers and users resulted in the committee being re-activated for the purpose of revising the standard.Under Sectional Committee,B94 Cutting Tools,the former Technical Committee TC-2 of B5 was reorganized an
7、d designated TC-1,Carbide and Oxide Tools.The next revision was approved by the B94 Sectional Committee on September 27,1965 and submitted to the sponsor ASME for submission to ASA for approval.ASA approval was granted on January 21,1966 and the standard designated B94.5-1966.The current revision wa
8、s approved by the American National Standards Insti-tute on June 6,1974.iii Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license
9、 from IHS-,-,-m 9009275 0024040 223 m AMERICAN NATIONAL STANDARDS COMMITTEE B94 CUTTING TOOLS,HOLDERS,DRIVERS AND BUSHINGS(The following i s the roster of the committee at the time of the approval of the Standard)O F F I C E RS Harry J.Moffott,Choinnan A.M.Mezey,Vice-Chairman Harry McLinden,Secretar
10、y STANDARDS COMMITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE f.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York G.L.Scott,alternate,American Gear Manufacturers Associations,Washington,D.C.M.E.Merchant,Dr.,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detro
11、it,Michigan C.J.Oxford,Jr.,National Twist Drill&Tool Company,Rochester,Michigan G.F.Wilson,alternate,DoAl1 Company,Des Plaines,Illinois w.E.Montgomery,Firth Sterling,Inc.McKeesport,Pennsylvania A.f.Wherry,dternate,Cemented Carbide Producers Association,Cleveland,Ohio w.c.f etrie,General Services Adm
12、inistration,Washington,D.C.W.A.Wagner,Cleveland Twist Drill Company,Cleveland,Ohio R.M.Byrne,alternate,Metal Cutting Tool Institute,New York,N.Y.R.J.Gargrave,Dayton Progress Corporation,Dayton,Ohio J.R.P idgeon,National Bureau of Standards,Washington,D.C.NATIONAL MACHINE TOOL BUILDERS ASSOCIATION G.
13、F.Wilson,DoAI1 Company,Des Plaines,Illinois E.J.Loeffler,alternate,National Machine Tool Builders Association,McLean,Virginia A.J.McLaren,The Cross Company,Fraser,Michigan W.H.Seocord,international Harvester Company,Hinsdale,Illinois W.N.Moore,The Ford Motor Co.,Dearborn,Michigan AMERICAN SOCIETY OF
14、 MECHANICAL ENGINEERS,THE CEMENTED CARBIDE PRODUCERS ASSOCIATION GENERAL SERVICES ADMINISTRATION METAL CUTTING TOOL INSTITUTE NATIONAL ASSOCIATION O F PUNCH MANUFACTURERS NATIONAL BUREAU OF STANDARDS SOCIETY OF AUTOMOTIVE ENGINEERS SOCIETY OF CARBIDE ENGINEERS C.H.Lang,Society of Carbide Engineers,B
15、ridgeville,Pennsylvania K.A.Lundell,The Producto Machine Company,Jamestown,New York H.J.Moffatt,Caterpillar Tractor Company,East Peoria,Illinois L.L.Parrish,Western Electric Company,Inc.,Chicago,Illinois S.f.Rogacki,alternate.Western Electric Company,Inc.,Kearney,New Jersey Representative to be appo
16、inted SOCIETY OF MANUFACTURING ENGINEERS TELEPHONE GROUP,THE U.S.DEPARTMENT O F THE AIR FORCE iv Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024041 1b8 US.DEPARTMENT OF THE ARMY R.K.Freeman,Liaison,U.S-Dept.of the Army,Rock Island,Illinois J.N.Segura,alternate,H q.,U.S.Army Weapons Command,Rock I