ImageVerifierCode 换一换
格式:PDF , 页数:6 ,大小:86.74KB ,
资源ID:182726      下载积分:11 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/182726.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_1795_-_13_2021.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_1795_-_13_2021.pdf

1、Designation:D179513(Reapproved 2021)Standard Test Method forIntrinsic Viscosity of Cellulose1This standard is issued under the fixed designation D1795;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number

2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the intrin-sic viscosity of purified celluloses such as bleached woodpulps,cotton linters,and regene

3、rated cellulose.It is applicableto all cellulose samples with an intrinsic viscosity of 15 dL/g orless.Most native(unpurified)celluloses have intrinsic viscos-ity values too high for measurement by this test method.NOTE1The use of cuprammonium hydroxide solution for regularviscosity determination is

4、 described in Method T 206 m-55 of theTechnical Association of Pulp and Paper Industry on“CuprammoniumDisperse Viscosity of Pulp,”and Joint Army-Navy Specifications JAN-C-206.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.

5、3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 Th

6、is international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(

7、TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids(and Calculation of Dynamic Viscos-ity)D629 Test Methods for Quantitative Analysis of TextilesE1 Specification for ASTM Liquid-in-Glass ThermometersE2251 Specification for

8、 Liquid-in-Glass ASTM Thermom-eters with Low-Hazard Precision Liquids3.Summary of Test Method3.1 Aweighed sample of the material is dissolved in a 0.5 Mcupriethylenediamine hydroxide solution.The viscosity of thissolution,and also that of the solvent,is determined at 25C bymeans of a calibrated glas

9、s capillary-type viscometer.Therelative viscosity is calculated and the corresponding intrinsicviscosity is read from a table.4.Significance and Use4.1 This test is a sensitive measure of the degradation ofcellulose resulting from the action of heat,light,acids,alkalies,oxidizing and reducing agents

10、,and the like,used in itsprocessing or purification.The intrinsic viscosity value may beconverted to degree of polymerization(DP)or to intrinsicfluidity,if desired.4.2 Solutions of cellulose are not Newtonian liquids;that is,their viscosity depends upon the rate-of-shear or velocitygradient during m

11、easurement.This effect is smaller for samplesof low molecular mass(DP)and at low concentrations than forhigh-DP samples and at high concentrations.For the cellulosesand concentrations included within the limits set forth in thistest method,the effect of rate-of-shear is assumed to benegligible for r

12、eferee purposes.For other conditions and forresearch purposes this assumption may be invalid,but todiscuss ways of accounting for this effect is beyond the scopeof the present test method.5.Apparatus5.1 Viscometer,Glass,Capillary TypeThe Cannon-Fenske,Ubbelohde,or similar capillary type instrument a

13、sdescribed in Test Method D445 is recommended.In order toavoid correction for the kinetic energy effect,choose a viscom-eter with a small enough capillary to give an outflow time of 80s or more for the Cannon-Fenske type.(A size 100 viscometeris normally used for the sample solution and a size 50 fo

14、r thesolvent.)5.2 ThermometerASTM Kinematic Viscosity Thermom-eter for use at 25C,having a range from 19 to 27C andconforming to the requirement for Thermometer 17C asprescribed in Specification E1.Thermometric devices such as1This test method is under the jurisdiction of ASTM Committee D01 on Paint

15、and Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.36 on Cellulose and Cellulose Derivatives.Current edition approved June 1,2021.Published June 2021.Originallyapproved in 1960.Last previous edition approved in 2013 as D1795 13.DOI:10.1520/D1795-13R21

16、.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principl

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2