ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:90.58KB ,
资源ID:185489      下载积分:12 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/185489.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_C_639_-_15.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_C_639_-_15.pdf

1、Designation:C63915Standard Test Method forRheological(Flow)Properties of Elastomeric Sealants1This standard is issued under the fixed designation C639;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number

2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method describes a laboratory procedure forthe det

3、ermination of rheological(flow)properties of single-and multicomponent chemically curing sealants for use inbuilding construction.1.2 Other suitable flow characteristics may be agreed uponbetween the seller and purchaser or specifier.Special nonsagproperties and lower flow characteristics may be req

4、uired foruse in sloping joints where absolute leveling is not desired.NOTE1The sealants are supplied in various rheological propertiesranging from pourable fluids to stiff nonsagging pastes.Multicomponentsealants are supplied as a base component with an activator or curingagent separately packaged.A

5、fter mixing the multiple parts,the sealant isready for application.Single-component sealants are supplied ready foruse upon opening of the package and usually depend on the externalenvironment for cure.1.3 This test method describes four types of joint sealants:1.3.1 Type ISingle-component flowable

6、or self-leveling,1.3.2 Type IISingle-component nonsag,1.3.3 Type IIIMulticomponent flowable or self-leveling,and1.3.4 Type IVMulticomponent nonsag.1.4 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard does not pu

7、rport to address the safetyproblems associated with its use.It is the responsibility of theuser of this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2C717 Terminology of B

8、uilding Seals and Sealants3.Terminology3.1 DefinitionsRefer to Terminology C717,Section 4.1,for definitions of the following terms used in this standard:chemically curing sealants,compound,elastomeric,flow(slump),non-sag sealant(non-slump),sealant,self-levelingsealant(flowable),standard conditions.4

9、.Comparison to Other Standards4.1 ISO7390:1987BuildingConstruction-JointingProducts-Determination of Resistance to Flow5.Significance and Use5.1 The results obtained from this test method are simply ameasure of the degree of horizontal or vertical flow ofsingle-component or multi-component sealants

10、when appliedto a set joint configuration at two pre-determined temperatures.Only samples conditioned at the same temperature may bedirectly compared.6.Apparatus6.1 Refrigerator,controlled at 4.4 6 2C(40 6 3.6F).6.2 Oven,convention-type,controlled at 50 6 2C(12263.6F).6.3 Channel,one,stainless steel(

11、Type 304,No.2-B finish,No.16 gage),inside dimensions 19 mm wide,13 mm deep,152 mm long(34by12by 6 in.),and closed at both ends(seeFig.1a).1This test method is under the jurisdiction ofASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.20 onGeneral T

12、est Methods.Current edition approved June 1,2015.Published August 2015.Originallyapproved in 1969.Last previous edition approved in 2011 as C639 01(2011).DOI:10.1520/C0639-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Ann

13、ual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.4 Channels,two,stainless steel(Type 304,No.2-B finish,No.16 gage),inside dimens

14、ions 19 mm wide,13 mm deep,152 mm long(34by12by 6 in.)with both ends open and theback surface extended 51 mm(2 in.)(see Fig.1b).7.Standard Test Conditions7.1 Unless otherwise specified,standard conditions shall bedefined in Terminology C717.8.Procedures8.1 Test for Type I Sealants:8.1.1 Clean the cl

15、osed-end channel(Fig.1a)with methylethyl ketone or similar solvent followed by a thorough cleaningwith a detergent solution and a final rinse with distilled ordeionized water,and then air dry.8.1.2 Before preparing the test assembly,condition at least100 g of the compound under test in the unopened

16、container forat least 16 h at standard conditions.Then condition thecompound for 16 to 24 h and the channel for 2 h in arefrigerator held at 4.4 6 2C(40 6 3.6F).At the end of theconditioning periods,pour the compound into the conditionedchannel held horizontally at the latter temperature and maintainthe test specimen at this temperature for 4 h.At the end of thisperiod,examine the compound for flow properties.8.2 Tests for Type II Sealants:8.2.1 Vertical SlumpBefore preparing the test assemblies

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2