1、Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-The American Society of Mechanical Engineers AMERICAN NATIONAL STANDARD FLAT TIP SCREWDRIVERS ASME B107.15-2002(R e v i s i o n of ASME B107.1!-i!)Copy
2、right ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-Date of issuance:January 15,2003 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda issued to t
3、his edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Interpretations are published on the ASME Web site under the Committee Pages at http:/www.asme.org/codes/as they are issued.ASME is the registered trademark of The American Society o
4、f Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportu
5、nity to participate.The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary devic
6、e,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liabilityfor infringement of any applicable letters patent,nor assume
7、any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is
8、not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies,which precludes the issuance of interpretations by individuais.No pa
9、rt of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 Copyright O 2003 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEER
10、S All rights reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-CONTENTS Foreword.iv Standards Committee Roster.v Correspondence With the B107 Committee.vi 1 Scope.1 2 Classifi
11、cation.1 3 Normative References.1 4 Definitions(See Fig.1).1 5 Requirements.2 6 Test Procedures.3 7 Designations.6 Figures 1 Descriptions.1 2 Typical Appearances.2 3 Fiat Tip Screwdriver Nomenclature at t1.2 4 Typical Appearance of a Cushion Grip Screwdriver.3 4 5B Cross Section of Slot for Typical
12、Torsional Test Block.5 6 Bending Moment Test.Typical Setup.6 Tables 1 Dimensional Characteristics of Flat Tip Screwdrivers.3 2 Performance Characteristics of Flat Tip Screwdrivers.4 3 impact Test Data.5 5A Typical Torsional Test Block.iii Copyright ASME International Provided by IHS under license wi
13、th ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-FOREWORD The American National Standards Committee B107,Socket Wrenches and Drives,under sponsorship of The American Society of Mechanical Engineers,was reorganized as an ASME Standards Committee,and its title wa
14、s changed to Hand Tools and Accessories.In 1996 its scope was expanded to address safety considerations.The purposes of this Standard are to define general and dimensional data and safety considerations specifically applicable to flat tip screwdrivers and to specify test methods to evaluate performa
15、nce relating to the defined requirements.This Standard is a revision of ASME B107.15-1993 Flat Tip and Phillips Screwdrivers.Principal changes in this Standard are the exclusion of Phillips screwdrivers(which can now be found in ASME B107.30-2002 Cross Tip Screwdrivers)and the addition of safety con
16、siderations.The format of this Standard is in accordance with The ASME Codes and Standards Writing Guide 2000.Requests for interpretations of the technical requirements of this Standard should be expressed in writing to the Secretary,B107 Committee,at the address below.Suggestions for the improvement of this Standard are welcome.They should be addressed to The American Society of Mechanical Engineers,Secretary,B107 Standards Committee,Three Park Avenue,New York,NY 10016-5990.The requirements of
