1、Nylon Insert Locknuts(Inch Series)AN AMERICAN NATIO NAL STANDARDASME B18.16.6-2008Copyright ASME International Provided by IHS under license with ASME Licensee=FMC Technologies/5914950002 Not for Resale,05/13/2009 00:34:18 MDTNo reproduction or networking permitted without license from IHS-,-,-ASME
2、B18.16.6-2008Nylon InsertLocknuts(Inch Series)AN AMERICAN NATIONAL STANDARDCopyright ASME International Provided by IHS under license with ASME Licensee=FMC Technologies/5914950002 Not for Resale,05/13/2009 00:34:18 MDTNo reproduction or networking permitted without license from IHS-,-,-Date of Issu
3、ance:November 24,2008This Standard will be revised when the Society approves the issuance of a new edition.There willbe no addenda issued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard.Periodically certain actions of the ASME
4、B18 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under proced
5、ures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpu
6、blic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity o
7、f any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that det
8、ermination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or sta
9、ndard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval sys
10、tem or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2008 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright ASME International Provided by IHS und
11、er license with ASME Licensee=FMC Technologies/5914950002 Not for Resale,05/13/2009 00:34:18 MDTNo reproduction or networking permitted without license from IHS-,-,-CONTENTSForeword.ivCommittee Roster.vCorrespondence With the B18 Committee.vi1Introduction.12Reference Standards.13Terminology.14Dimens
12、ions.15Nut Designs and Property Grades.16Width Across Flats.17Corner Fill.28Height.29Hex Height.210Threads.211Material,Mechanical,and Performance Properties.412Test Methods.413Grade and Manufacturing Marking.614Inspection and Quality Assurance.615Dimensional Conformance.616Designation.617Workmanship
13、.6Tables1Nut Dimensions.22Proof Loads,Clamp Loads,and Prevailing-Torques for Coarse Thread SeriesGrades NE2,NE5,and NE8 Nuts.33Proof Loads,Clamp Loads,and Prevailing-Torques for Fine Thread SeriesGrades NE2,NE5,and NE8 Nuts.34Chemical Composition Requirements.45Hardness Requirements.4iiiCopyright AS
14、ME International Provided by IHS under license with ASME Licensee=FMC Technologies/5914950002 Not for Resale,05/13/2009 00:34:18 MDTNo reproduction or networking permitted without license from IHS-,-,-FOREWORDASME B18.16.6-2008 was balloted and approved by the B18 Standards Committee and B18Subcommi
15、ttee 16 on April 29,2008.The proposal was submitted to the American NationalStandards Institute and designated as an American National Standard on August 25,2008.ivCopyright ASME International Provided by IHS under license with ASME Licensee=FMC Technologies/5914950002 Not for Resale,05/13/2009 00:3
16、4:18 MDTNo reproduction or networking permitted without license from IHS-,-,-ASME B18 COMMITTEEStandardization of Bolts,Nuts,Rivets,Screws,Washers,and Similar Fasteners(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSD.A.Clever,ChairR.D.Strong,Vice ChairR.L.Crane,Staff SecretarySTANDARDS COMMITTEE PERSONNELV.Cartina,Continental-AeroD.A.Clever,Deere&Co.A.P.Cockman,Ford Motor Co.B.D.Burnside,Alternate,Ford Motor Co.R.L.Crane,The Am