1、AN AMERICAN NATIONAL STANDARD Metric Small Solid Rivets ANSI/ASME B18.1.3M-1983 REAFFIRMED 1995 12 mm Nominal Diameter and Smaller Government Key Words:Rivet,Solid,Small-Metric FOR CURRENT COMMllTEE PERSONNEL PLEASE SEE ASME MANUAL AS-1 1 SPONSORED AND PUBLISHED B Y T H E A M E R I C A N S O C I E T
2、 Y OF M E C H A N I C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.10017 REAFFIRMED 2021Date of Issuance:March 31,1984 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the
3、 requirements of this Standard issued to this Edition.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerne
4、d interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agen-cies,and the public-at-large.ASME does not approve,rate,or endorse any it
5、em,construction,proprietan/device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any appl
6、icable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or pers
7、on(s)affiliated with industry is not to be interpreted as government or in,dustry endorsement of this code or standard.ASME does not accept any responsibility for interpretations of this document made by individual volunteers.No part of this document may be reproduced in any form,in an electronic re
8、trieval system or otherwise without the prior written permission of the publisher.Copyright 1984 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.ERRATA OCTOBER 1985 to ANSI/ASME B18.1.3M-1983 METRIC SMALL SOLID RIVETS Page 4,Table 3-Under Main dimension 12.0 for
9、Ds Min,correct 12.80 to read 11 3 0 Page 5,Table 4-(1)Under Main dimension 12.0 for Ds Min,correct(2)Under Main dimension 4.0 for Head(DK)Basic(K)12.80 to read 11.80 Min,correct 2.35 to read 2.25 M0131E THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS 345 East 47th Street,New York,N.Y.10017 M0131 E Inte
10、ntionally left blank FOREWORD(This Foreword is not a part of ANSVASME 618.1.3M-1983,Metric Small Solid Rivets.)American National Standards Committee B18 for the standardization of bolts,screws,nuts,rivets,and similar fasteners was organized in March 1922 as Sectional Committee B18 under the aegis of
11、 the American Engineering Standards Committee (later the American Standards Association,then the United States of America Standards Institute and,as of October 6,1969,the American National Standards Institute,Inc.),with the Society of Automotive Engineers and the American Society of Mechanical Engin
12、eers as joint sponsors.Subcommittee 1 was subsequently established and charged with the responsibility for technical content of standards covering solid rivets.At its meeting on December 4,1974,Committee B18 authorized preparation of a series of standards for metric fasteners.Subcommittee 1 was assi
13、gned responsibility for developing standards for metric solid rivets.In February 1978,Committee B18 established a cooperative program with the Department of Defense to draft American National Standards for metric fasteners in such a way that they could be used directly by the Government for procurem
14、ent purposes.The Department of Defense requested that each product be covered in separate standards,and Subcommittee 1 accepted this approach.This Standard was approved by letter ballot of Committee B18 on February 4,1983,and was subsequently approved by the sponsor and submitted to the American Nat
15、ional Standards Institute for designation as an American National Standard.This was granted on September 8,1983.111.Intentionally left blank ASME STANDARDS COMMITTEE B18 Standardization of Bolts,Nuts,Rivets,Screws,Washers,and Similar Fasteners OFFICERS J.B.Levy,Chairman H.W.Ellison,Vice-chairman E.S
16、chwartz.Vice-chairman R.McGinnis,Secretary COMMllTEE PERSONNEL AMERICAN SOCIETY OF AGRICULTURAL ENGINEERS E.R.Friesth,Coal Valley,Illinois AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE K.E.McCullough,SPS Technologies,Jenkintown,Pennsylvania A.R.Machell,Jr.,Webster,New York C.R.Adams,Alternate,Newport News Shipbuilding&Dry Dock Company,Newport News,Virginia ENGINE MANUFACTURERS ASSOCIATION G.A.Russ,Cummins Engine Company,Columbus,Indiana FARM&INDUSTRIAL EQUIPMENT INSTITUTE D.A.Clever,Deere&Company
