1、ASME B5.61-2003Power Presses:General Purpose,Single Action,Straight SideTypeAN AMERICAN NATIONAL STANDARDSThe American Society ofMechanical EngineersThree Park Avenue.New York,NY 10016e5a2686o216oCONTENTSForewordCommittee Roster.viCorrespondence With the B5 Committee.vii1 Scope,Purpose,and Applicati
2、on。44。4。4442Definitions and Terminology3 Metric/U.S.Customary Rationalization4Press characteristics.5Tooling Related Characteristics6Acceptance Conditions.137 Health and Safety168Information and Instructions.169Declaration of Manufacturers Compliance.1910Reference Standards。，19Figures1Slide Connecti
3、ons for Single-Point,Two-Point,and Four-Point Presses.2Drives for Single-Point,Two-Point,and Four-Point Presses.33Typical Construction of a Mechanical Press.44Typical Construction of a Hydraulic Press.5Typical Bolster.156Typical Slide.157Headed Pressure Pin.178Headed Pressure Pinhole.19Pressure Pinh
4、ole Location Identification System.10Establishing the Bed as the Datum Plane.811Bolster Flatness and Parallelism.1912Checking Parallelism From Slide Face to Bed or Bolster Surface.13Checking Squareness of Slide Travel.2014Leveling the Slide Using Load Cells.15Press Data Plate:Mechanical Press.2116Pr
5、ess Data Plate:Hydraulic Press.17Counterbalance Data Plate.2118Die Cushion Data Plate.Press Designation System.22220Press Capability Graph(Metric).321Press Capability Graph(U.S.Customary).Tables1Standard Capacity Ratings2Standard Rating Points.i进No reproduction or networking pemmitted without licens
6、e from IHSNot for Resale,05/13/200900:22:49 MDT3Press Speed/Drive Motor Relationship.4Usable Flywheel Energy.23Stroke and Die Space Dimensions:Mechanical Power Press.6Bed and Slide Dimensions:Single-Point Press.55Bed and Slide Dimensions:Two-Point and Four-Point Press.6Bolster Locating Pin Dimension
7、s.79Spacing of Bolster Locating Pinholes:Single-Point Press.10Spacing of Bolster Locating Pinholes:Two-Point and Four-Point Press.11Bolster Mounting Slot Dimensions.912Spacing of Bolster Mounting Slots:Single-Point Press.91Spacing of Bolster Mounting Slots:Two-Point and Four-Point Press.1014Bolster
8、Mounting Bolt Dimensions.1Bolster Handling Holes:Single-Point Press.216Bolster Handling Holes:Two-Point and Four-Point Press.1317Bolster Handling Hook Dimensions.118Bolster Handling Hook Bolt Dimensions.419Number of T-Slots.16Plain Pressure Pin.121Pressure Pinhole Patterns.2Pressure Pinhole Plug.18M
9、andatory AppendicesIMechanical Power Press Capacity Above Rating Point of 12.7 mm(0.5 in.).25Mechanical Power Press Capacity Above Rating Point of 6.3 mm(0.25 in.).6Mechanical Power Press Capacity Above Rating Point of 1.6 mm(0.06 in.).27IVUsable Flywheel Energy.8Bed and Slide Deflection.2VIOffset L
10、oading of a Mechanical Press Slide.Nonmandatory AppendicesAMetric/U.S.Customary Conversion.31Comparison of Capacity Ratings Between Historical JIC and ISOStandards32ivee=FMC Technol9591495000No reproduction or networking pemmitted without license from IHSN6Rg5e.0S93209602249Mo7FOREWORDRecognizing th
11、e need for a standard for mechanical power presses,the ASME Committee onMachine Tools and Components(B5)established in December 1973,Technical Committee 30 todevelop an American National Standard addressing the interchangeability of bolsters,presstooling,and mounting provisions between general purpo
12、se presses of comparable bed size,capacity,and type.The B5-TC30 membership consists of a balance between manufacturers,users,accessory suppli-ers and others associated with power presses.The technical committees work was based on theJoint Industry Conference(JIC)Press Room Standards,once the most wi
13、dely used document,todevelop a standard for mechanical power presses,and basic data submitted by U.S.manufacturersof power presses.In April 1983,the committee completed the final draft of Standard for Straight Side TypePresses(Metric).This draft was not submitted for approval before the committee be
14、came inactive.In 1995,Technical Committee 30 was reestablished to continue the pursuit of the originalobjectives set forth in 1973.The scope of the Standard was expanded to include hydraulic powerpresses.ASME B5.61-2003 was approved by the American National Standards Institute on July 7,2003.w591495000所No reproduction or networking pemmitted without license from IHSNot for Resale,05/13/200900:22:49 MDT
