1、Designation:D90620Standard Test Method forStrength Properties of Adhesives in Plywood TypeConstruction in Shear by Tension Loading1This standard is issued under the fixed designation D906;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisi
2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.INTRODUCTIONThe accuracy of the re
3、sults of strength tests of adhesive bonds will depend on the conditions underwhich the bonding process is carried out.Unless otherwise agreed upon between the manufacturer andthe purchaser,the bonding conditions shall be prescribed by the manufacturer of the adhesive.In orderto ensure that complete
4、information is available to the individual conducting the tests,themanufacturer of the adhesive shall furnish numerical values and other specific information for each ofthe following variables:(1)The moisture content of the wood at the time of bonding.(2)Complete mixing directions for the adhesive.(
5、3)Conditions for application of the adhesive including the rate of spread or thickness of film,number of coats to be applied,whether more than one coat is required.(4)Assembly conditions before application of pressure,including the room temperature,length oftime,and whether open or closed assembly i
6、s to be used.(5)Curing conditions,including the amount of pressure to be applied,the length of time underpressure and the temperature of the assembly when under pressure.It should be stated whether thistemperature is that of the bond line,or of the atmosphere at which the assembly is to be maintaine
7、d.(6)Conditioning procedure before testing,unless a standard procedure is specified,including thelength of time,temperature,and relative humidity.A range for any variable or combination of variables is permitted provided any arbitrarily chosenvalue within the range or combinations specified is accep
8、table to both the manufacturer and thepurchaser of the adhesives.1.Scope1.1 This test method covers the determination of the com-parative shear strengths of adhesives in plywood-typeconstruction,when tested on a standard specimen and underspecified conditions of preparation,conditioning,and testing.
9、This test method is intended to be applied only to adhesivesused in bonding wood to wood.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are provided forinformation purposes only.1.3 This standard does not purport to address all of thesafety concer
10、ns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with interna
11、tionally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D907 Termin
12、ology of Adhesives1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved April 1,2020.Published May 2020.Originallyapproved in 1947.Last previous edition approved in 2017 as D906
13、98(2017).DOI:10.1520/D0906-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Bar
14、r Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendat
15、ions issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.D1038 Terminology Relating to Veneer,Plywood,and WoodStructural PanelsD4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsD5266 Practice for Estimating the Percentage of Wood
16、Failure in Adhesive Bonded Joints3.Terminology3.1 Definitions:3.1.1 Many terms in this test method are defined in Termi-nology D907 and Terminology D1038.3.1.2 plywood,na panel generally flat built up of layers ofveneer called plies,united under pressure by an adhesive tocreate a panel with the bond between the plies as strong as,orstronger than,the wood,and that has the following character-istics:(1)is constructed of an odd number of layers with grainof adjacent layers perpendicular,(2)with a l
