1、Designation:D95199(Reapproved 2010)Standard Test Method forWater Resistance of Shipping Containers by Spray Method1This standard is issued under the fixed designation D951;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of l
2、ast revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determinati
3、on of the waterresistance of shipping containers.1.2 This test method is frequently used in conjunction withother tests made prior to or after the spray test,such as the droptest,vibration test,inclined impact test,or compression test.1.3 The values stated in inch-pound units are to be regardedas st
4、andard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this stan
5、dard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D685 Practice for Conditioning Paper and Paper Productsfor TestingD996 Terminology of Packaging and Distribution Environ-ments3
6、.Terminology3.1 DefinitionsFor definitions of terms used in this testmethod,refer to Terminology D996.4.Significance and Use4.1 This test method is used to determine the water resis-tance of shipping containers.It can be used to determine theability of the container to resist deterioration caused by
7、 wateror the ability of the container to protect the contents fromwater.It is frequently used in conjunction with other tests madeprior to or after the spray test,such as the drop test,inclinedimpact test,vibration test or compression test.5.Apparatus5.1 The apparatus,illustrated schematically in Fi
8、g.1,shallconsist of the components described in 5.2 5.8.Modificationsare permissible,such as the use of fresh tap water instead of arecirculating system,as long as the specified temperature andspray intensity are achieved.5.2 Test RoomA test room or cabinet shall be of water-resistant construction,i
9、nsulated and heated when necessary sothat proper temperature control can be maintained.The bottomshall be covered with a false floor of slats and have an outletdrain.5.3 SpraysSpray nozzles shall be of such size and sospaced that the specified intensity of spray falls uniformlydistributed over the f
10、loor area.The spray nozzles shall be solocated that the droplets are falling from gravitational forceonly when they strike the specimens.5.4 Flow Control ValvesFlow control valves,to controlthe intensity of the spray,are required.5.5 Circulating SystemA circulating system shall,whereused,consist of
11、a fine-mesh strainer,pump,relief by-pass,gages,and pressure regulating valve,together with the neces-sary piping between the flow control valves,spray nozzles,andwater reservoir.5.6 ReservoirA reservoir for storage and conditioning ofthe spray water shall,where used,be equipped with anoverflow to a
12、sewer and with a drain to facilitate changing thewater at the start of each test.Make-up water,regulated by afloat control,shall also discharge into this tank.5.7 Water Temperature ControlA thermostatically con-trolled means of heating for maintaining the supply water at thedesired temperature is re
13、quired.5.8 Conditioning ApparatusAdequate facilities shall beprovided for conditioning test specimens at proper humidityand temperature prior to test.1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.21 on ShippingConta
14、iners and Systems-Application of Performance Test Methods.Current edition approved April 1,2010.Published May 2010.Originallyapproved in 1947.Last previous edition approved in 2004 as D951 99(2004).DOI:10.1520/D0951-99R10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact A
15、STM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Test Specimens6.1 Test at least
16、three containers,closed and sealed as forshipping.Select as test specimens samples that are represen-tative of the containers being tested.For some purposes(suchas for checking leakage alone)the containers may be testedempty.Normally,however,the containers shall be packed withthe contents designed to be shipped in them or with a materialof similar character.7.Conditioning7.1 Condition the test specimens sufficiently,after closingand sealing,so that any adhesives,protective coatings,gluedflaps,an
