1、Designation:D984 97(Reapproved 2007)Technical Association of Pulp and Paper IndustryStandard Method T 406 Su-72An American National StandardStandard Test Methods forReducible Sulfur in Paper1This standard is issued under the fixed designation D984;the number immediately following the designation ind
2、icates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the determination of re
3、duciblesulfur in paper and paperboard within the context of the givendefinitions.1.1.1 Method AThe quantitative method gives a measureof the reducible sulfur with much greater accuracy.2,31.1.2 Method BThe semiquantitative method indicates thegeneral level of reducible sulfur with limited accuracy.1
4、.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Docume
5、nts2.1 ASTM Standards:4D585 Practice for Sampling and Accepting a Single Lot ofPaper,Paperboard,Fiberboard,and Related ProductD644 Test Method for Moisture Content of Paper andPaperboard by Oven DryingD1968 Terminology Relating to Paper and Paper ProductsD2043 Test Method for Silver Tarnishing by Pa
6、per3.Terminology3.1 DefinitionsDefinitions shall be in accordance withTerminology D1968 and the Dictionary of Paper.54.Summary of Test Methods4.1 Method A,the quantitative method,uses the identicalreduction system to generate hydrogen sulfide,but the sulfideis precipitated by alkaline cadmium sulfat
7、e and then convertedtomethylenebluebyreactionwithacidicp-aminodimethylaniline in the presence of ferric chloride.Themethylene blue is measured spectrophotometrically and theintensity is compared with standards prepared in similarmanner.4.2 Method B,semiquantitative method,involves the reduc-tion of
8、various forms of sulfur to hydrogen sulfide and thedevelopment of a dark spot of lead sulfide on the filter paperimpregnated with lead acetate.The intensity of the spot iscompared with spots developed from standards and is propor-tional to the concentration.No colorimeter or spectrophotom-eter is ne
9、eded for this method.5.Significance and Use5.1 The test methods outlined are not necessarily a measureof how much a given test material will tarnish polished metals.When tested by these methods,paper that has less than0.0008%reducible sulfur,may be assumed to be nontarnishingas far as sulfur is conc
10、erned,but if more than 0.0008%,thisdoes not necessarily mean that tarnishing will occur,becausesulfur compounds which may not cause staining are reduced bythe treatment with the subsequent evolution of hydrogensulfide.If more than 0.0008%reducible sulfur is found,or ifthe effect of that or other mat
11、erials causing stains on silver isdesired,the paper should be subjected to an acceleratedtarnishing test(see Test Method D2043).NOTE1If the pH of the paper is low(for example,4.0 to 4.5(coldextraction)as little as 0.0002%of reducible sulfur may cause tarnishingof imitation gold bronze prints;whereas
12、,if the pH were higher,(forexample,on brush-coated art paper)a much higher quantity of sulfurmight be tolerated.5.2 The test methods described do not give the total sulfurcontent,nor the total reducible sulfur content,nor are theyintended to.They are limited to the reducible sulfur contentdetermined
13、 under the conditions of the test(that is,a fairlymild reduction system).31These test methods are under the jurisdiction of ASTM Committee D06 onPaper and Paper Products and are the direct responsibility of Subcommittee D06.92on Standard Documents Relating to Paper and Paper Products.Current edition
14、 approved Dec.1,2007.Published December 2007.Originallyapproved in 1948.Last previous edition approved in 2002 as D984 97(2002).DOI:10.1520/D0984-97R07.2Sobolev,I.,Bhargava,R.,Gosuntov,N.,and Russell,R.,Tappi,Vol 39,No.9,1956,p.628.3Chazin,J.D.,“Colorimetric Determination of Reducible Sulfur in Pape
15、r andPaperboard,”Tappi,Vol 53,No.8,1970,p.1514.4For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.5Available from Tec
16、hnical Association of the Pulp and Paper Industry(TAPPI),15 Technology Parkway South,Norcross,GA 30092,http:/www.tappi.org.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.NOTICE:This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest information5.2.1 Those forms of sulfur believed to be“reducible”underthe test conditions are(1)sulfide(released by the ac
