收藏 分享(赏)

ASTM_E_1137_-_E_1137M_-_08_2014.pdf

上传人:益****师 文档编号:168482 上传时间:2023-03-04 格式:PDF 页数:7 大小:167.03KB
下载 相关 举报
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第1页
第1页 / 共7页
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第2页
第2页 / 共7页
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第3页
第3页 / 共7页
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第4页
第4页 / 共7页
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第5页
第5页 / 共7页
ASTM_E_1137_-_E_1137M_-_08_2014.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:E1137/E1137M08(Reapproved 2014)Standard Specification forIndustrial Platinum Resistance Thermometers1This standard is issued under the fixed designation E1137/E1137M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the yea

2、r of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the requirements for metal-sheathed industrial platinum resistance thermometers(PRTs)suitab

3、le for direct immersion temperature measurement.Itapplies to PRTs with an average temperature coefficient ofresistance between 0 and 100C of 0.385%C and nominalresistance at 0C of 100 or other specified value.Thisspecification covers PRTs suitable for all or part of thetemperature range 200 to 650C.

4、The resistance-temperaturerelationship and tolerances are specified as well as physical,performance,and testing requirements.1.2 The values of temperature in this specification are basedon the International Temperature Scale of 1990(ITS-90).21.3 The values stated in inch-pound units or SI(metric)uni

5、ts may be regarded separately as standard.The values statedin each system are not exact equivalents,and each system shallbe independent of the other.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this stan

6、dard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3A269 Specification for Seamless and Welded AusteniticStainless Steel Tubing for General ServiceB167 Specification for Nickel-Ch

7、romium-Iron Alloys(UNSN06600,N06601,N06603,N06690,N06693,N06025,N06045,andN06696),Nickel-Chromium-Cobalt-Molybdenum Alloy(UNS N06617),and Nickel-Iron-Chromium-Tungsten Alloy(UNS N06674)Seamless Pipeand TubeE344 Terminology Relating to Thermometry and Hydrom-etryE644 Test Methods for Testing Industri

8、al Resistance Ther-mometersE1652 Specification for Magnesium Oxide and AluminumOxide Powder and Crushable Insulators Used in theManufacture of Base Metal Thermocouples,Metal-Sheathed Platinum Resistance Thermometers,and NobleMetal Thermocouples3.Terminology3.1 DefinitionsFor definitions of terms use

9、d in this speci-fication see Terminology E344.3.2 Definitions of Terms Specific to This Standard:3.2.1 connecting wire end closure,nmoisture barrier atthe connecting wire end of the sheath.3.2.1.1 DiscussionThe closure is intended to provide aseal sufficient to prevent the sensors insulation resista

10、nce fromdropping below the minimum requirements.3.2.2 connecting wires,nwires that run from the elementthrough the connecting wire end closure and external to thesheath.3.2.3 excitation,nelectrical current passing through theelement.3.2.4 g-level,nacceleration of an object relative to thelocal accel

11、eration of gravity.3.2.4.1 DiscussionFor example,a g-level of 5 is equiva-lent to an acceleration of approximately 5 9.8 m/s2=49.0m/s2.3.2.5 minimum immersion length,ndepth that a thermom-etershouldbeimmersed,inauniformtemperatureenvironment,such that further immersion does not produce achange in in

12、dicated temperature greater than the specifiedtolerance.3.2.6 PRT design,ngeneric term used to differentiatebetween different PRT construction details,such as elementand connecting wire construction,insulation methods,sealingtechniques,and mounting methods(for example,spring loadedor direct mounting

13、).1This specification is under the jurisdiction of ASTM Committee E20 onTemperature Measurement and is the direct responsibility of Subcommittee E20.03on Resistance Thermometers.Current edition approved Dec.1,2014.Published December 2014.Originallyapproved in 1987.Last previous edition approved in 2

14、008 as E1137 08.DOI:10.1520/E1137_E1137M-08R14.2Preston-Thomas,H.,“The International Temperature Scale of 1990(ITS-90),”Metrologia,Vol 27,No.1.1990,pp 3 10,ibid,Vol 27,No.2,1990,p1073For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.

15、For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.7 self-heating,nchange in temperature of the elementcaused by the heat

16、ing effect of the excitation.3.2.8 sheath,ncylindrical metal tube with an integralwelded closure at the end in which the element is located.4.Significance and Use4.1 This specification is written to provide commonterminology,resistance versus temperature characteristics,ac-curacy classification,and inspection requirements for a speci-fied configuration of a typical industrial platinum resistancethermometer(PRT).4.2 This specification may be used as part of the documen-tation to support negotiati

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2