1、Designation:E197611Standard Specification forShelter,Tactical,Nonexpandable1This standard is issued under the fixed designation E1976;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses i
2、ndicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This specification covers a rigid wall,nonexpandableshelter constructed of alumin
3、um-faced,nonmetallic honey-comb sandwich panels,and meeting the International Organi-zation for Standardization(ISO)Cargo Container specification.Nominal dimensions are:height 8 ft,width 8 ft and length 20ft(2.4 by 2.4 by 6.1 m).1.2 The values stated in inch-pound units are to be regardedas the stan
4、dard.The SI units given in parentheses are forinformation only.1.3 The following precautionary statement pertains to thetest method portion only,Section 7,of this specification:Thisstatement does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibility
5、of the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E864 Practice for Surface Preparation of Aluminum Alloysto Be Adhesively Bonded in Honeycomb Shelter Panels
6、E865 Specification for Structural Film Adhesives for Hon-eycomb Sandwich PanelsE866 Specification for Corrosion-Inhibiting AdhesivePrimer for Aluminum Alloys to Be Adhesively Bonded inHoneycomb Shelter PanelsE874 Practice for Adhesive Bonding of Aluminum Facingsto Nonmetallic Honeycomb Core for Shel
7、ter PanelsE990 Specification for Core-Splice Adhesive for Honey-comb Sandwich Structural PanelsE1091 Specification for Nonmetallic Honeycomb Core forUse in Shelter PanelsE1749 Terminology Relating to Rigid Wall RelocatableSheltersE1773 Practice for Sealing Rigid Wall Tactical Shelters withPolysulfid
8、e Based SealantsE1826 Specification for Low Volatile Organic Compound(VOC)Corrosion-Inhibiting Adhesive Primer for Alumi-num Alloys to Be Adhesively BondedE1925 Specification for Engineering and Design Criteria forRigid Wall Relocatable Structures2.2 ISO Standards:3ISO 1161-1980 Series 1-Freight Con
9、tainers-Corner Fittings,SpecificationISO 1496/I Series 1-Freight Containers-Specification andTesting Part I-General Cargo ContainersISO 9001 Quality Systems-Model for Quality Assurance inDesign,Development,Production,Installation,and Ser-vicing2.3 Military Standards:4MIL-STD-129 Marking for Shipping
10、 and StorageMIL-STD-810 Environmental Engineering Considerationsand Laboratory Tests2.4 ANSI/ASQC Standard:5ANSI/ASQC Z1.4-1993 Sampling Procedures and Tablesfor Inspection by Attributes2.5 Drawings:65-4-3141 Shelter,Assembly,Non-Expandable-60 amp5-4-6865 Shelter,Assembly,Non-Expandable-100 amp2.6 S
11、AE Standards:7SAE-AMS-STD-1595 Qualification ofAircraft,Missile,andAerospace Fusion Welders1This specification is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Subcommittee E06.53on Materials and Processes for Durable Rigidwall Relocatabl
12、e Structures.Current edition approved Sept.1,2011.Published October 2011.Originallyapproved in 1998.Last previous edition approved in 2005 as E1976 05.DOI:10.1520/E1976-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual
13、 Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,Sectio
14、nD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.5Available from American Society for Quality(ASQ),600 N.Plankinton Ave.,Milwaukee,WI 53203,http:/www.asq.org.6Copies of drawings are available from U.S.Army Natick Soldier Center,ATTN:AMSRD-NSC-CP-CS,KansasStreet,Natick,MA01760-50
15、18,http:/www.army.mil/info/organization/natick.7Available from SAE International(SAE),400 Commonwealth Dr.,Warrendale,PA 15096-0001,http:/www.sae.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 SAE-AMS-STD-2219 Fusion Welding for Aero
16、space Appli-cations3.General Requirements3.1 Alternate ComponentsWhen this specification or thereferenced drawings specify use of a specific component“orequal,”the contractor may substitute a component equal to thespecified component provided that the contractor complieswith the following requirements.Prior to manufacture of thefirst article,or if none is required,prior to commencingproduction,the contractor shall submit for the purchasersapproval,a list identifying each proposed“or equal”compo-
