1、Designation:D781113(Reapproved 2022)Standard Test Method forBow and Skew Using a Measuring Tool1This standard is issued under the fixed designation D7811;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num
2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is used to determine the bow and skewof woven and knitted fabrics over a fixed distance,using ameasuring tool.1.2 This test m
3、ethod is useful when a small specimen or cutparts need to be evaluated for bow and skew,provided a warpor fill,or both,reference line is available,to aid in aligning thetool.1.3 Test Method D3882 may be used when measuring bowand skew in fabric in rolls.However,results obtained withD3882 may not be
4、comparable with results obtained by this testmethod.1.4 There is no known ISO equivalent standard.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns,if any,
5、associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally r
6、ecognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Rela
7、ting to TextilesD1776 Practice for Conditioning and Testing TextilesD3882 Test Method for Bow and Skew in Woven andKnitted FabricsD3990 Terminology Relating to Fabric DefectsE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study
8、 toDetermine the Precision of a Test Method3.Terminology3.1 For all terminology related to fabric defect terms,referto Terminology D3990.3.1.1 The following terms are relevant to this standard:bow,double bow,double hooked bow,double reverse bow,hookedbow,knitted fabric,skew,standard atmosphere for t
9、estingtextiles.3.2 For all other terminology related to textiles,refer toTerminology D123.4.Summary of Test Method4.1 A straightedge is placed across the fabric between twopoints at which a marked filling yarn,knitted course,desig-nated printed line,or designated design meets the two selvagesor edge
10、s.The greatest distance between the straightedge andthe marked filling line,knitted course,designated printed line,or designated design is measured parallel to the selvage.5.Significance and Use5.1 This test method provides a standard procedure forobtaining data for research and development,quality
11、control,acceptance and rejection under specifications,and for specialpurposes.5.2 The data obtained by this test method is applicable to thematerial under the conditions of this particular test and is notnecessarily the same as obtained under other environments inuse.5.3 This test method is consider
12、ed satisfactory for accep-tance testing of commercial shipments.5.4 If there are differences of practical significance betweenreported test results for two laboratories(or more),compara-tive tests should be performed to determine if there is astatistical bias between them,using competent statistical
13、 assis-tance.As a minimum,the test samples to be used are as1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.60 on Fabric Physical TestMethods B.Current edition approved June 1,2022.Published July 2022.Originally approve
14、din 2013.Last previous edition approved in 2017 as D7811-13(2017).DOI:10.1520/D7811-13R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary
15、page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theD
16、evelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1homogeneous as possible,are drawn from the material fromwhich the disparate test results were obtained,and are ran-domly assigned in equal numbers to each laboratory for testing.Other fabrics with established test values may be used for thispurpose.The test results from the two laboratories should becompared using a statistical test for unpaired data,
