1、Designation:D7250/D7250M20Standard Practice forDetermining Sandwich Beam Flexural and Shear Stiffness1This standard is issued under the fixed designation D7250/D7250M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last r
2、evision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers determination of the flexural andtransverse shear stiffness properties of flat sandwich construc-tions subje
3、cted to flexure in such a manner that the appliedmoments produce curvature of the sandwich facing planes.Permissible core material forms include those with continuousbonding surfaces(such as balsa wood and foams)as well asthose with discontinuous bonding surfaces(such as honey-comb).The calculation
4、methods in this practice are limited tosandwich beams exhibiting linear force-deflection response.This practice uses test results obtained from Test MethodsC393/C393M or D7249/D7249M,or both.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.T
5、hevalues stated in each system are not necessarily exact equiva-lents;therefore,to ensure conformance with the standard,eachsystem shall be used independently of the other,and valuesfrom the two systems shall not be combined.1.2.1 Within the text,the inch-pound units are shown inbrackets.1.3 This st
6、andard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This intern
7、ational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Commi
8、ttee.2.Referenced Documents2.1 ASTM Standards:2C273 Test Method for Shear Properties of Sandwich CoreMaterialsC393/C393M Test Method for Core Shear Properties ofSandwich Constructions by Beam FlexureD883 Terminology Relating to PlasticsD3878 Terminology for Composite MaterialsD7249/D7249M Test Metho
9、d for Facesheet Properties ofSandwich Constructions by Long Beam FlexureE6 Terminology Relating to Methods of Mechanical TestingE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or ProcessE177 Practice for Use of the Terms Precisio
10、n and Bias inASTM Test MethodsE456 Terminology Relating to Quality and Statistics3.Terminology3.1 DefinitionsTerminology D3878 defines terms relatingto high-modulus fibers and their composites,as well as termsrelating to sandwich constructions.Terminology D883 definesterms relating to plastics.Termi
11、nology E6 defines termsrelating to mechanical testing.Terminology E456 and PracticeE177 define terms relating to statistics.In the event of aconflict between terms,Terminology D3878 shall have prece-dence over the other terminologies.3.2 Symbols:b=sandwich width,mm in.c=core thickness,mm in.d=sandwi
12、ch thickness,mm in.D=flexural stiffness,N-mm2lb-in.2=beam mid-span deflection,mm in.G=core shear modulus,MPa psiS=support span length,mm in.L=load span length,mm in.(L=0.0 for 3-point mid-spanloading configuration)n=number of specimens1This practice is under the jurisdiction of ASTM Committee D30 on
13、 CompositeMaterials and is the direct responsibility of Subcommittee D30.09 on SandwichConstruction.Current edition approved July 1,2020.Published August 2020.Originallyapproved in 2006.Last previous edition approved in 2016 as D7250/D7250M 16.DOI:10.1520/D7250_D7250M-20.2For referenced ASTM standar
14、ds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959
15、.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barr
16、iers to Trade(TBT)Committee.P=total applied force,N lbt=facing thickness,mm in.U=transverse shear rigidity,N lb4.Summary of Practice4.1 This practice consists of calculating the flexuralstiffness,transverse(through-thickness)shear rigidity,and coreshear modulus of a sandwich beam using deflection or straindata,or both,from two or more flexure tests of differentloading configurations conducted under Test Methods C393/C393M or D7249/D7249M,or both.This practice also in-cludes equations for calcula
