1、Designation:D771218Standard Terminology forSampling and Analysis of Asbestos1This standard is issued under the fixed designation D7712;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses
2、indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This terminology standard is a collective vocabularyrelating to sampling and analysis of asbestos.As a convenienceto general interest,it contains most of the sta
3、ndard terms,definitions,and nomenclature under the jurisdiction of Com-mittee D22.1.2 Many of the entries in this terminology are copied(withattribution)from the standards of origin referenced in Section2.The standards of origin are noted in bold type at the rightmargin of the applicable definition.
4、1.3 Certain terms in the common language that comprisemultiple concepts are included herein with the definitionspecific to standards and practices of Committee D22.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established
5、in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:D1356 Terminology Relating to Sampling and Analysis ofAtmospheresD5755 Test
6、 Method for Microvacuum Sampling and IndirectAnalysis of Dust by Transmission Electron Microscopyfor Asbestos Structure Number Surface LoadingD5756 Test Method for Microvacuum Sampling and IndirectAnalysis of Dust by Transmission Electron Microscopyfor Asbestos Mass Surface Loading(Withdrawn 2017)2D
7、6281 Test Method for Airborne Asbestos Concentration inAmbient and Indoor Atmospheres as Determined byTransmission Electron Microscopy Direct Transfer(TEM)D6480 Test Method for Wipe Sampling of Surfaces,IndirectPreparation,and Analysis for Asbestos Structure NumberSurface Loading by Transmission Ele
8、ctron MicroscopyD6620 Practice for Asbestos Detection Limit Based onCountsD7200 Practice for Sampling and Counting Airborne Fibers,Including Asbestos Fibers,in Mines and Quarries,byPhase Contrast Microscopy and Transmission ElectronMicroscopyD7201 Practice for Sampling and Counting Airborne Fibers,I
9、ncluding Asbestos Fibers,in the Workplace,by PhaseContrast Microscopy(with an Option of TransmissionElectron Microscopy)D7390 Guide for Evaluating Asbestos in Dust on Surfacesby Comparison Between Two Environments2.2 Government Standards:USGS Open-File Report 02-458 Tabulation of Asbestos-Related Te
10、rminology3.Terminologyacicular,adjthe shape shown by an extremely slender crystalwith cross-sectional dimensions that are small relative to itslength,that is,needle-like.D6281activity generated aerosol,na dispersion of particles in airthat have become airborne due to physical disturbances suchas hum
11、an activity,sweeping,airflow,etc.D7390amphibole,na group of more than 60 different silicateminerals with similar crystal structures and complex com-positions that conform to the nominal formula:A021B2C5T8O22OH,F,Cl!2where:A=K,Na,Ca;B=Fe2+,Mn,Mg,Ca,Na;C=Al,Cr,Ti,Fe3+,Mg,Fe2+;andMn and T=Si,Al,Cr,Fe3+
12、,Ti.In some varieties of amphibole,these elements can bepartially substituted by Li,Pb,Zn,Be,Ba,or Ni.Amphibolesare characterized by a complex monoclinic or orthorhombicstructure that includes a double chain of T-O tetrahedra with aT:O ratio of approximately 4:11;a variable morphology thatranges fro
13、m columnar to prismatic to acicular to fibrous;andgood prismatic cleavage at angles of about 56 and 124.Thecleavage may not be readily exhibited by small crystals that arebound by irregular growth and fracture surfaces.D62811This terminology standard is under the jurisdiction of ASTM Committee D22on
14、 Air Quality and is the direct responsibility of Subcommittee D22.07 on Samplingand Analysis of Asbestos.Current edition approved April 15,2018.Published June 2018.Originallyapproved in 2011.Last previous edition approved in 2011 as D7712 111.DOI:10.1520/D7712-18.2The last approved version of this h
15、istorical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decisio
16、n on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 amphibole asbestos,namphibole in an asbestiform habit.D6281D6480analytical sensitivity,nthe calculated airborne asbestosstructure concentration in asbestos structures/L,equivalentto the counting of one asbestos structure in the analysis.D6281nthe calculated airborne asbestos structure concentrationin asbestos structures/square
