1、Designation:D766215(Reapproved 2020)Standard Test Method forCarbon Content in Carbon Black Feedstock Oils1This standard is issued under the fixed designation D7662;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the instrumental determinationof carbon content in samples of carbon black feedstock oils.Values obtained re
3、present the total carbon content.1.2 This test method is applicable to carbon black feedstockoils derived from petroleum,coal,and other sources whichinclude fuel oils,residues,tars,pitches,reclaimed oils,andsimilar materials that are normally handled as liquids.This testmethod is applicable to produ
4、cts that typically contain 75 to 94mass%carbon.1.3 The results of these tests can be expressed as mass%carbon.1.4 UnitsThe values stated in SI units are to be regardedas standard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety
5、 concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with
6、internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D405
7、7 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesD7633 Test Method for Carbon BlackCarbon Con
8、tent3.Summary of Test Method3.1 In this test method,a sample of feedstock oil is weighedin a combustion boat containing a tungsten oxide basedaccelerator and the carbon content is determined by placing theboat in a tube furnace at 1350C in an air-or oxygen-enrichedatmosphere resulting in complete co
9、mbustion.Carbon in thesample is completely oxidized to carbon dioxide.Moisture andparticulates are removed from the gas stream by traps filledwith anhydrous magnesium perchlorate.The gas stream is thenpassed through a cell in which carbon dioxide concentration ismeasured by an infrared(IR)absorption
10、 detector at a precisewavelength in the IR spectrum.3.2 This test method is for use with commercially availablecarbon analyzers equipped to carry out the combustion andmeasurement operations automatically.3.3 The carbon analyzer shall be calibrated using an appro-priate calibration standard(see 6.5)
11、.3.4 The instrument may be configured to analyze more thanone element such as a carbon-sulfur analyzer.In this case,theanalyzer has individual detectors for each element that arearranged in series.4.Significance and Use4.1 Measuring the total carbon content of feedstock oil isoften a necessary compo
12、nent in calculations for carbon dioxideemissions,estimating yield of a process,or assessing productquality.4.2 The carbon black industry measures carbon content offeedstock oils along with carbon content of carbon blackproducts per Test Method D7633 for Carbon Black-CarbonContent in calculations to
13、determine carbon dioxide emissionsfor compliance with governmental greenhouse-gas-reportingrequirements.1This test method is under the jurisdiction of ASTM Committee D24 on CarbonBlack and is the direct responsibility of Subcommittee D24.66 on Environment,Health,and Safety.Current edition approved N
14、ov.1,2020.Published December 2020.Originallyapproved in 2010.Last previous edition approved in 2015 as D7662 15.DOI:10.1520/D7662-15R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume inform
15、ation,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization esta
16、blished in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.Apparatus5.1 There are a number of commercial instruments availablethat are designed to measure carbon content in organic mate-rials including carbon and carbon-sulfur analyzers.This testmethod makes no specifications regarding system designs.5.2 Functionally,however,the following are specified for allin