1、Designation:D761912bStandard Test Method forSizing and Counting Particles in Light and Middle DistillateFuels,by Automatic Particle Counter1,2This standard is issued under the fixed designation D7619;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method uses a specific automatic particlecounter2(APC)to count and measure the size o
3、f dispersed dirtparticles,water droplets and other particles,in light and middledistillate fuel,and bio fuels such as biodiesel and biodieselblends,in the overall range from 4 m(c)to 100 m(c)and inthe size bands 4 m(c),6 m(c),and 14 m(c).NOTE1ASTM and military specification fuels falling within thes
4、cope of this test method include Specifications:D975 grades 1D and 2D,D1655,D3699,D4814(see 14.1.1.1),D6751,D7467,distillate grades ofD396 and D2880,MIL-DTL-83133,and MIL-DTL-16884.NOTE2For the purposes of this test method,water droplets arecounted as particles,and agglomerated particles are detecte
5、d and countedas a single larger particle.Dirt includes biological particles.Although theprojected area of a particle is measured,this is expressed as the diameterof a sphere for the purposes of this test method.NOTE3The notation(c),used with particle sizes,is used to denotethat the apparatus has bee
6、n calibrated in accordance with ISO 11171.Strictly this only applies to particles up to 50 m.NOTE4This test method may be used for particle sizes bands up to100 m(c),however the precision has only been determined for the sizebands 4 m(c),6 m(c),and 14 m(c).All measurements are per mL.1.2 The values
7、stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and
8、 health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3D396 Specification for Fuel OilsD975 Specification for Diesel Fuel OilsD1655 Specification for Aviation Turbine FuelsD2880 Specification for Gas Turbine Fuel OilsD3699
9、Specification for KerosineD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4814 Specification for Automotive Spark-Ignition EngineFuelD5854 Practice for Mixing and Handling of Liquid Samplesof Petroleum and
10、Petroleum ProductsD6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products andLubricantsD6751 Specification for Biodiesel Fuel Blend Stock(B100)for Middle Distillate FuelsD7467 Specification for Diesel Fuel Oil,Biodiesel Blend(B6 to B20)2.2 ASTM Adjun
11、cts:4ADJ6300 D2PP Determination of Precision and Bias datafor Use in Test Methods for Petroleum Products2.3 ISO Standards:5ISO 11171 Hydraulic Fluid PowerCalibration of Auto-matic Particle Counters for LiquidsISO 4406 Hydraulic Fluid PowerFluidsMethod forCoding Level of Contamination by Solid Partic
12、lesISO 12103-A1 Specification for Ultra Fine Test Dust(UFTD)ISO 12103-A3 Specification for Medium Test Dust(MTD)1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.14 on Stability and C
13、leanliness of Liquid Fuels.Current edition approved Dec.1,2012.Published March 2013.Originallyapproved in 2010.Last previous edition approved in 2012 as D761912a.DOI:10.1520/D7619-12B.2The sole source of the apparatus known to the committee at this time isSETA-AvCount,available from Stanhope-Seta,Lo
14、ndon Street,Chertsey,SurreyKT16 8AP UK.If you are aware of alternative suppliers,please provide thisinformation to ASTM International Headquarters.Your comments will receivecareful consideration of a meeting of the responsible technical committee,1whichyou may attend.3For referenced ASTM standards,v
15、isit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Out of print.5Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,
16、New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.4 U.S.Dept.of Defense Specifications:6MIL-DTL-83133 Turbine Fuel,Aviation,Kerosene Type,JP-8(NATO F-34),NATO F-35,and JP-8+100(NATOF-37)MIL-DTL-16884 Fuel,Naval Distillate3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 particles,nsolid particles and dispersed wate
