1、Designation:D6630/D6630M16Standard Guide forLow Slope Insulated Roof Membrane AssemblyPerformance1This standard is issued under the fixed designation D6630/D6630M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revis
2、ion.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide lists test methods intended to establish aminimum level of performance for insulated roof membraneassemblies,and lists per
3、tinent design guidelines and installa-tion methods in a unified manner.Material tests and evalua-tions are included with and without roof insulation.1.2 It is not possible to establish a precise correlationbetween laboratory tests on roof assemblies and natural weath-ering due to variations in geogr
4、aphical climate,design,mate-rial and installation.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the
5、two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bilit
6、y of regulatory requirements prior to use.2.Referenced Documents2.1 ASTM Standards:2D95 Test Method for Water in Petroleum Products andBituminous Materials by DistillationD450/D450M Specification for Coal-Tar Pitch Used inRoofing,Dampproofing,and WaterproofingD1079 Terminology Relating to Roofing an
7、d WaterproofingD2523 Practice for Testing Load-Strain Properties of Roof-ing MembranesD4434/D4434M Specification for Poly(Vinyl Chloride)Sheet RoofingD4637/D4637M Specification for EPDM Sheet Used InSingle-Ply Roof MembraneD4798/D4798M Practice for Accelerated Weathering TestConditions and Procedure
8、s for Bituminous Materials(Xenon-Arc Method)D4799/D4799M Practice for Accelerated Weathering TestConditions and Procedures for Bituminous Materials(Fluorescent UV,Water Spray,and Condensation Method)D5019 Specification for Reinforced CSM(ChlorosulfonatedPolyethylene)Sheet Used in Single-Ply Roof Mem
9、brane(Withdrawn 2011)3D5147/D5147M Test Methods for Sampling and TestingModified Bituminous Sheet MaterialD5601 Test Method for Tearing Resistance of Roofing andWaterproofing Materials and Membranes(Withdrawn2002)3D5602/D5602M Test Method for Static Puncture Resistanceof Roofing Membrane SpecimensD5
10、635/D5635M Test Method for Dynamic Puncture Resis-tance of Roofing Membrane SpecimensD5849/D5849M Test Method for Evaluating Resistance ofModified Bituminous Roofing Membrane to Cyclic Fa-tigue(Joint Displacement)D6754/D6754M Specification for Ketone Ethylene EsterBased Sheet RoofingD6878/D6878M Spe
11、cification for Thermoplastic PolyolefinBased Sheet RoofingE96/E96M Test Methods for Water Vapor Transmission ofMaterialsE631 Terminology of Building Constructions2.2 ASCE Standard:ASCE-7 Minimum Design Loads for Buildings and OtherStructures41This guide is under the jurisdiction of ASTM Committee D0
12、8 on Roofing andWaterproofing and is the direct responsibility of Subcommittee D08.20 on RoofingMembrane Systems.Current edition approved July 1,2016.Published August 2016.Originallyapproved in 2001.Last previous edition approved in 2008 as D6630 08.DOI:10.1520/D6630_D6630M-16.2For referenced ASTM s
13、tandards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Ava
14、ilable from American Society of Civil Engineers(ASCE),1801 AlexanderBell Dr.,Reston,VA 20191,http:/www.asce.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.3 ANSI/SPRI Standard:ANSI/SPRI RP-4 Wind Design Guide for Ballasted SinglePl
15、y Roof Systems53.Terminology3.1 For terminology used in this standard,refer to Termi-nologies D1079 and E631.3.2 roof assembliesthe weathering or waterproofingmaterial,whether film,flexible membrane,semi-flexiblemembrane,factory or field manufactured;the underlyingsubstrate including insulation(if u
16、sed)above or below themembrane,or both;supporting deck structure and method ofattachment of the entire assembly.Low slope roof assembliesmay be up to 25%slope.Some roof assemblies may accom-modate higher slopes.3.3 performancethe ability of the roof system as designed,manufactured,and installed to provide adequate levels ofexpected service life in terms of watertightness,thermalprotection,and condensation control,while being maintain-able.Live loading of the roof system may also occur.4.Signific
