1、Designation:D644709(Reapproved 2014)Standard Test Method forHydroperoxide Number of Aviation Turbine Fuels byVoltammetric Analysis1This standard is issued under the fixed designation D6447;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revis
2、ion,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 The test method covers the determination of the hydrop-eroxide content of aviation turbine fuels.The test m
3、ethod mayalso be applicable to the determination of the hydroperoxidecontent of any water-insoluble,organic fluid,particularlydiesel fuels,gasolines,and kerosines.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This stand
4、ard does not purport to address all the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to consult and establish appropriatesafety and health practices and determine the applicability ofregulatory limitations prior to use.For specific warningstateme
5、nts,see 6.3 6.5,Annex A1,and Annex A2.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD3703 Test Method for Hydroperoxide Number of AviationTurbine Fuels,Gasoline and Diesel FuelsD4057 Practice for Manual Sampling of Petroleum andPetroleum Products3.Summary of Test Met
6、hod3.1 A quantity of sample is contacted with aqueous potas-sium iodide solution in the presence of acid.The hydroperox-ides present are reduced by the potassium iodide.An equiva-lent amount of iodine is liberated,which is quantified byvoltammetric analysis.The results are calculated and reportedas
7、millimoles(mmole)of hydroperoxide per litre of sample.4.Significance and Use4.1 This test method and Test Method D3703 measure thesame peroxide species(primarily hydroperoxides)in aviationfuels.4.2 The magnitude of the hydroperoxide number is anindication of the quantity of oxidizing constituents pr
8、esent.Deterioration of fuel results in the formation of hydroperoxidesand other oxygen-carrying compounds.The hydroperoxidenumber measures those compounds that will oxidize potassiumiodide.4.3 The determination of the hydroperoxide number of fuelsis significant because of the adverse effect of hydro
9、peroxidesupon certain elastomers in the fuel systems.5.Apparatus5.1 Voltammetric Analyzer3The instrument used to quan-tify the liberated iodine is a voltammetric analyzer equippedwith a three electrode system and a digital or analog output.The combination electrode system(see Fig.1)consists of aglas
10、sy carbon disc(3-mm diameter)working electrode,aplatinum wire(0.5 mm diameter)auxiliary electrode,and aplatinum wire(0.5 mm diameter)reference electrode.Thevoltammetric analyzer applies a linear voltage ramp(0 to 1 Vrange with respect to the reference electrode)at a rate of 0.1V/s to the auxiliary e
11、lectrode.The current output of theworking electrode is converted to voltage by the voltammetricanalyzer,using the gain ratio of 1V/20A.The peak height orpeak area of the voltammetric response to iodine is outputted toan analog or digital recording device(0 to 1 V full scale).5.2 Vortex Mixer,4with a
12、 2800 to 3000 rpm motor and a padsuitable for mixing test tubes and vials.5.3 Pipette,or equivalent,capable of delivering volumesrequired in the test method,such as 0.2,1,and 2 mL.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is
13、 the direct responsibility ofSubcommittee D02.05 on Properties of Fuels,Petroleum Coke and Carbon Material.Current edition approved May 1,2014.Published July 2014.Originally approvedin 1999.Last previous edition approved in 2009 as D6447 09.DOI:10.1520/D6447-09R14.2For referenced ASTM standards,visi
14、t the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Voltammetric analyzers specifically designed to perform hydroperoxide valuedeterminations of aviatio
15、n turbine fuels are commercially available from TheUniversity of Dayton Research Institute.Voltammographs,which can be set up toperform hydroperoxide value determinations of aviation turbine fuels,are availablefrom BAS,West Lafayette,IN and EG&G Princeton Applied Research,Princeton,NJ.4Vortex mixers
16、 suitable for mixing the prepared standard and sample solution areavailable from Barnstead/Thermolyne,Dubuque,IA and Fisher Scientific Co.,Pittsburgh,PA.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.4 Volumetric Flasks(optional),100 and 500 mL capacity.5.5 Glass Vials,5 or 10 mL capacity.6.Reagents and Materials6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests.Unless otherwise indicated,it is intended thatall
