1、Designation:D826222Standard Test Method forDetermining the pH of Granular Material for Use inEmbankments,Subgrades,and Retaining Wall Backfil1This standard is issued under the fixed designation D8262;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method uses a pH meter to measure the pH ofas-received granular material that represen
3、ts what will be usedin the field for embankments,subgrades,and retaining wallbackfill applications.The principal use of the test method is tosupplement soil resistivity measurements to identify conditionsunder which the corrosion of metal embedded in granularmaterial,or in contact with the granular
4、material may besharply accentuated.1.2 The pH of granular material is often specified byagencies to meet criteria that are necessary to prevent or reducecorrosion of metal objects embedded in the granular materialused in embankments,subgrade,and retaining wall backfill.1.3 The types of granular mate
5、rial that can be tested for pHusing this standard are natural or manufactured coarse sand,natural or crushed stone,natural or crushed gravel,air-cooledblast furnace slag,and aggregates:lightweight,heavyweight,or normal weight.According to AASHTO M 145,thesegranular materials generally fall into AASH
6、TO classificationgroups A-1,A-2-4,A-2-5,or A-3.The ideal material is awell-graded,free draining material that has less than 10-15%passing the 75 m(No.200)sieve.1.4 This test is based on the volumetric method because theunit weight of the fill material will vary depending on sourceand project specifi
7、cations.1.5 UnitsThe values stated in SI units are to be regardedas standard.Except the sieve designations,they are identifiedusing the“alternative”system in accordance with SpecificationE11,such as 3 in.and No.200,instead of the“standard”of 75mm and 75 m,respectively.No other units of measurementar
8、e included in this standard.Reporting of test results in unitsother than SI shall not be regarded as nonconformance withthis standard.1.6 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026,unless superseded by this test
9、method.1.6.1 The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that generally should be retained.The proce-dures used do not consider material variation,purpo
10、se forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to becommensurate with these considerations.It is beyond the scopeof these test methods to consider significant digits u
11、sed inanalysis methods for engineering data.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability
12、 of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World
13、Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C125 Terminology Relating to Concrete and Concrete Ag-gregatesC702/C702M Practice for Reducing Samples of Aggregateto Testing SizeD75/D75M Practice for Sampling AggregatesD653 Terminology Relating t
14、o Soil,Rock,and ContainedFluidsD1193 Specification for Reagent WaterD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD4972 Test Methods for pH of Soils1This test method is under the jurisdiction ofA
15、STM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.06 on Physical-ChemicalInteractions of Soil and Rock.Current edition approved March 1,2022.Published March 2022.DOI:10.1520/D8262-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact AST
16、M Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issue
