收藏 分享(赏)

ASTM_D_7147_-_21.pdf

上传人:益****师 文档编号:173768 上传时间:2023-03-04 格式:PDF 页数:11 大小:371.94KB
下载 相关 举报
ASTM_D_7147_-_21.pdf_第1页
第1页 / 共11页
ASTM_D_7147_-_21.pdf_第2页
第2页 / 共11页
ASTM_D_7147_-_21.pdf_第3页
第3页 / 共11页
ASTM_D_7147_-_21.pdf_第4页
第4页 / 共11页
ASTM_D_7147_-_21.pdf_第5页
第5页 / 共11页
ASTM_D_7147_-_21.pdf_第6页
第6页 / 共11页
亲,该文档总共11页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D714721Standard Specification forTesting and Establishing Allowable Loads of Joist Hangers1This standard is issued under the fixed designation D7147;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio

2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers a procedure for evaluatingmetal devices used for wood-to-wood,wood-to-concrete,wood-to-concrete masonry,and w

3、ood-to-steel connections.This method is intended for use with devices used to connectjoists,beams,and girders together.These devices are com-monly described as joist hangers.1.2 This specification describes test methods for evaluatingthe capacities of joist hangers subject to vertical and torsionall

4、oading.1.3 This specification provides a method of assigning allow-able loads to joist hangers based on measured strength anddeformation characteristics.Information obtained by the pro-visions of this specification is applicable to design when usingthe Allowable Stress Design method.1.4 UnitsThe val

5、ues stated in inch-pound units are to beregarded as standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with it

6、s use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principl

7、es on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C31/C31M Practice for Making and Curing

8、 Concrete TestSpecimens in the FieldC39/C39M Test Method for Compressive Strength of Cylin-drical Concrete SpecimensC90 Specification for Loadbearing Concrete Masonry UnitsC270 Specification for Mortar for Unit MasonryC1314 Test Method for Compressive Strength of MasonryPrismsD245 Practice for Estab

9、lishing Structural Grades and Re-lated Allowable Properties for Visually Graded LumberD9 Terminology Relating to Wood and Wood-Based Prod-uctsD1038 Terminology Relating to Veneer,Plywood,and WoodStructural PanelsD1761 Test Methods for Mechanical Fasteners in Wood andWood-Based MaterialsD2395 Test Me

10、thods for Density and Specific Gravity(Rela-tive Density)of Wood and Wood-Based MaterialsD3737 Practice for Establishing Allowable Properties forStructural Glued Laminated Timber(Glulam)D4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsD5055 Specification fo

11、r Establishing and Monitoring Struc-tural Capacities of Prefabricated Wood I-JoistsD5456 Specification for Evaluation of Structural CompositeLumber ProductsD7438 Practice for Field Calibration and Application ofHand-Held Moisture MetersE4 Practices for Force Verification of Testing MachinesE8/E8M Te

12、st Methods for Tension Testing of Metallic Ma-terialsE575 Practice for Reporting Data from Structural Tests ofBuilding Constructions,Elements,Connections,and As-sembliesF606/F606M Test Methods for Determining the MechanicalPropertiesofExternallyandInternally ThreadedFasteners,Washers,Direct Tension

13、Indicators,and RivetsF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance InspectionF1575 Test Method for Determining Bending Yield Momentof Nails1This specification is under the jurisdiction of ASTM Committee D07 on Woodand is the direct responsibility of Subcom

14、mittee D07.05 on Wood Assemblies.Current edition approved July 1,2021.Published August 2021.Last previousedition approved in 2018 as D7147 11(2018).DOI:10.1520/D7147-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Bo

15、ok of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized p

16、rinciples on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.2.2 Other Standards:AWC NDS National Design Specification for Wood Con-struction3AISI S100 North American Specification for the Design ofCold-Formed Steel Structural Members4ANSI/AISC 360 Specification for Structural Steel Build-ings5ANSI/ASME B18.2.1 Square,Hex,Heavy Hex,an

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2