收藏 分享(赏)

ASTM_D_7501_-_22.pdf

上传人:益****师 文档编号:174050 上传时间:2023-03-04 格式:PDF 页数:6 大小:142.71KB
下载 相关 举报
ASTM_D_7501_-_22.pdf_第1页
第1页 / 共6页
ASTM_D_7501_-_22.pdf_第2页
第2页 / 共6页
ASTM_D_7501_-_22.pdf_第3页
第3页 / 共6页
ASTM_D_7501_-_22.pdf_第4页
第4页 / 共6页
ASTM_D_7501_-_22.pdf_第5页
第5页 / 共6页
ASTM_D_7501_-_22.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D750122Standard Test Method forDetermination of Fuel Filter Blocking Potential of BiodieselFuel Blendstock(B100)by Cold Soak Filtration Test(CSFT)1This standard is issued under the fixed designation D7501;the number immediately following the designation indicates the year oforiginal adop

2、tion or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination by filtrationtime after cold soak fo

3、r the suitability of biodiesel fuelblendstock(B100)that meets all other requirements of Speci-fication D6751 and has a cloud point below 20 C(68 F)toprovide adequate low temperature operability performance toat least the cloud point of the finished blend.1.2 The values stated in SI units are to be r

4、egarded asstandard.Non-SI units are given for information only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-min

5、e the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations i

6、ssued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD6217 Test Method for Particulate C

7、ontamination in MiddleDistillate Fuels by Laboratory FiltrationD6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products,Liquid Fuels,and LubricantsD6751 Specification for Biodiesel Fuel Blend Stock(B100)for Middle Distillate Fuels3.Terminology3.1 Defi

8、nitions:3.1.1 For definitions of terms used in this test method,referto Terminology D4175.3.1.2 biodiesel,nfuel comprised of mono-alkyl esters oflong chain fatty acids derived from vegetable oils or animalfats,designated as B100.3.1.3 biodiesel blend(BXX),na homogeneous mixture ofhydrocarbon oils an

9、d mono-alkyl esters of long chain fattyacids.3.1.3.1 DiscussionIn the abbreviation,BXX,the XX rep-resents the volume percentage of biodiesel fuel in the blend.3.1.4 bond,vto connect two parts of a system electricallyby means of a conductive wire to eliminate voltage differences.3.2 Definitions of Te

10、rms Specific to This Standard:3.2.1 air chamber,nunit to control temperature of samplefor cooling with maximum 0.5 C variation from set point.Theunit shall use a microprocessor temperature controller withdigital set point and readout.Afood-grade refrigerator does notprovide adequate temperature stab

11、ility for this test method.3.2.2 minor component,nmaterial present in B100,typi-cally at concentrations well below 1%by mass.3.2.3 thermal history,nrange of temperatures that a batchor sample of B100 has experienced which can result inseparation or precipitation of minor components.3.2.3.1 Discussio

12、nCooling some biodiesel fuels can resultin precipitation or separation of minor components that havelimited solubility in B100.Heating these biodiesel fuels above40 C is believed to redissolve most of these minor compo-nents and thus erase the thermal history of the sample.3.3 Abbreviations:3.3.1 CS

13、FTCold Soak Filtration Test4.Summary of Test Method4.1 In this test method,300 mLof biodiesel(B100)is storedat 4.5 C 6 0.5 C(40 F 6 1 F)for 16 h,allowed to warm to25 C 6 1 C(77 F 6 2 F),and vacuum filtered through a1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Product

14、s,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.14 on Stability,Cleanliness and Compatibility of Liquid Fuels.Current edition approved April 1,2022.Published April 2022.Originallyapproved in 2009.Last previous edition approved in 2021 as D7501 21.DOI:10.1520/D7501-2

15、2.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standar

16、dCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1single 0.7 m glass fiber filter at controlled vacuum levels of70 kPa to 85 k

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2