1、Designation:D601300(Reapproved 2018)Standard Test Method forDetermination of Area Stability of Leather to Laundering1This standard is issued under the fixed designation D6013;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year o
2、f last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method2covers the determination of launder-ability of dyed leathers with or without a pigment finish.Thistest m
3、ethod does not apply to wet blue.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the u
4、ser of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in
5、the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D1610 Practice for Conditioning Leather and Leather Prod-ucts for Testing3.Si
6、gnificance and Use3.1 The procedure is primarily intended to evaluate theability of a leather specimen to withstand fixed,and ratherstrenuous,laundering conditions.This test method is notintended as a recommended washing procedure,neither house-hold nor commercial.The resulting area stability is det
7、ermined.4.Apparatus44.1 Washing MachineA Launder-Ometer,5or an assemblyof apparatus capable of similar test conditions(see Note).Ineither machine,1-pt(500-mL)specimen containers are heldwith their bases toward a horizontal shaft and 2 in.(50 mm)outfrom its center of rotation.Speed of rotation shall
8、be 40 to 45rpm.Provision shall be made for maintaining the initialtemperature of the specimen containers throughout the test.Additional agitation shall be provided by14-in.(6.4-mm)stainless steel balls in the specimen containers.Apparatus isillustrated in Figs.1-3.NOTE1A motor-driven assembly,design
9、ed to hold 1-pt(500-mL)specimen containers so that they are relative to the axis of the motor shaftin the same way as in the Launder-Ometer,can be used.5The entireassembly,fitted with specimen containers,shall be turned at 40 to 45 rpminside a simple boxlike container which is heated at 120F(49C)wit
10、hthermostatic control.Thus,heat loss from the preheated contents of thespecimen containers is held at a minimum during the 30-min washingperiods.Such an apparatus is illustrated in Figs.4 and 5.4.2 Stainless Steel Balls,type 316,14in.(6 mm)diameter.4.3 Steel or Glass Jar,1 pt(0.5 L),with washer and
11、cap.4.4 Circulating-air Oven,capable of maintaining the re-quired temperature of 120 6 2F(49 6 1C).4.5 Blotting Paper,6(laboratory)(see 7.2).4.6 Metal Die,for cutting the specimen to the requireddimensions.4.7 Soap Solution,7prepared by dissolving 5 g of standardneutral chip soap in 1 L of distilled
12、 water(see 7.3).1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.04 on Apparel.Current edition approved Nov.1,2018.Published November 2018.Originallyapproved in 1996.Last previous edition approved in 2010 as D6013-00(201
13、0).DOI:10.1520/D6013-00R18.2This test method was developed from Federal Test Method Standard No.311Method 3041.1 in cooperation with the U.S.Army Natick Research Developmentand Engineering Center,Natick,MA,and the Defense Personnel Support CenterDirectorate of Clothing and Textiles,Philadelphia,PA.3
14、For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The leather washing apparatus drawing is available from ASTM Headq
15、uarters,100 Barr Harbor Drive,W.Conshohocken,PA 194282959.Request AdjunctADJD6013.5The sole source of supply of the apparatus known to the committee at this timeis Atlas Electric Devices Co.,4114 N.Ravenswood Ave.,Chicago,IL 60613.If youare aware of alternative suppliers,please provide this informat
16、ion to ASTMHeadquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.6The sole source of supply of the apparatus known to the committee at this timeis Standard Paper Manufacturing Co.,P.O.Box 1554,Richmond,VA 23212.If youare aware of alternative suppliers,please provide this information to ASTMHeadquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may at
