1、Designation:D744609(Reapproved 2017)Standard Specification forStructural Insulated Panel(SIP)Adhesives for LaminatingOriented Strand Board(OSB)to Rigid Cellular PolystryeneThermal Insulation Core Materials1This standard is issued under the fixed designation D7446;the number immediately following the
2、 designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification is designed t
3、o evaluate adhesivessuitable for the bonding of oriented strand board(OSB)to rigidcellular polystyrene insulation core materials for general struc-ture use.1.2 The requirements of the structural insulated panel(SIP)adhesive are based on the performance of the adhesive asmeasured by:1.2.1 Resistance
4、to shear by compression loading in ambi-ent conditions and after accelerated aging.1.2.2 Resistance to tensile loading in ambient conditionsand after accelerated aging.1.2.3 Resistance to creep(deformation)under static load inambient conditions and after accelerated aging.1.2.4 Tensile and shear str
5、ength to polystyrene core materi-als.1.3 The classification of the adhesive formulation is basedon,but not limited to the adhesives industry accepted genericnames,for example:phenol-resorcinol,emulsion polymerisocyanate,one and two-part urethane.The type of adhesiveapplication and curing terminology
6、 are also usually includedfor classification purposes such as cold-setting phenolresorcinol,heat-cured phenol resorcinol,and hot melt onecomponent urethane.1.4 Evaluation of adhesive performance at high temperatureconditions,such as during a fire exposure,is beyond the scopeof this specification.1.5
7、 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-pria
8、te safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of Internati
9、onal Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C273/C273M Test Method for Shear Properties of SandwichCore MaterialsC297/C297M Test Method for Flatwise Tensile Strength ofSandwich Co
10、nstructionsC578 Specification for Rigid,Cellular Polystyrene ThermalInsulationD572 Test Method for RubberDeterioration by Heat andOxygenD905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD907 Terminology of AdhesivesD1183 Practices for Resistance of Adhesives to
11、 CyclicLaboratory Aging ConditionsD1583 Test Method for Hydrogen Ion Concentration of DryAdhesive FilmsD2294 Test Method for Creep Properties of Adhesives inShear by Tension Loading(Metal-to-Metal)D4300 Test Methods for Ability of Adhesive Films toSupport or Resist the Growth of FungiD4442 Test Meth
12、ods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsD4444 Test Method for Laboratory Standardization andCalibration of Hand-Held Moisture MetersE4 Practices for Force Verification of Testing Machines1This specification is under the jurisdiction of ASTM Committee D14 onAdhesi
13、ves and is the direct responsibility of Subcommittee D14.70 on ConstructionAdhesives.Current edition approved April 1,2017.Published May 2017.Originallyapproved in 2009.Last previous edition approved in 2009 as D7446 09.DOI:10.1520/D7446-09R17.2For referenced ASTM standards,visit the ASTM website,ww
14、w.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis internati
15、onal standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.
16、1 2.2 Other Standards:PS2 Performance Standard for Wood-Based Structural-UsePanels3ISO 17025 General Requirements for the Competence ofTesting and Calibration Laboratories43.Terminology3.1 DefinitionsMany terms in this specification are de-fined in Terminology D907.3.2 Definitions of Terms Specific to This Standard:3.2.1 core material,nlocated between structural insulatedpanel facings;for this specification,consists of rigid cellularpolystyrene thermal insulation,either expanded polystyrene(EPS)
